Swann SW244-8ML manual Internet & Network, Network Connection, Service Port & Ddns, Static IP

Page 30

SETUP

2.INTERNET & NETWORK

‰Set Network Connection and DDNS in INTERNET & NETWORK.

NETWORK CONNECTION

Press + buttons on remote controller to select NETWORK CONNECTION in SETUP menu.

zNETWORK TYPE Select either STATIC IP or DHCP.

A STATIC IP address is a number (in the form of a dotted quad) that is assigned to a computer by an Internet service provider (ISP) to be its permanent address on the Internet.

Short for Dynamic Host Configuration Protocol(DHCP), a protocol for assigning dynamic IP addresses to devices on a network.With dynamic addressing, a device may have a different IP address every time it connects to the network.

z IP ADDRESS

Type the IP Address when you select

 

STATIC IP.

z SUBNET MASK

Type the Subnet Mask when you select

 

STATIC IP.

z GATEWAY

Type the Gateway when you select

 

STATIC IP.

z PRIMARY DNS

Primary DNS is used to refer the DVR’s

 

IP address to a preferred domain name.

zSECONDARY DNS Secondary DNS is used to refer the DVR’s IP address for backup domain name.

NOTICE

When you select DHCP and press APPLY button , allocated IP information will be displayed.

SERVICE PORT & DDNS

Press + buttons on remote controller to select SERVICE PORT & DDNS in SETUP menu.

zWEB SERVICE PORT Type the web service port number. (Port No: 1 ~ 65534)

z USE DDNS

If you want to use DDNS, please select

 

here.

z DDNS ID

Type the DDNS Name.

z CHECK ID

Please click the CHECK ID button for

 

register and change settings.

NOTICE

When WEB SERVICE PORT was set by 80 in 2. INTERNET & NETWORK - SERVICE PORT & DDNS menus, type ip address or domain into the address bar in Microsoft® Internet Explorer™ However, when port number is not 80, you must type port number behind IP address or domain. (ex. http://IP address or domain:port number)

If the registered DDNS ID is “dvr” and DDNS SERVER is “webdvr.net”, you can connect to the DVR by entering the full domain name,“dvr.webdvr.net”, through the Microsoft® Internet Explorer™ If your DVR is installed under a firewall or internet sharing router, you should set port forwarding, DMZ and other settings.

28

Image 30
Contents Quick Start Guide Safety Precautions Table of Contents Product Introduction Package Contents Front Panel Direction Buttons Move cursorRear Panel 8 Chan Rear Panel Convention used in this ‰ Backup Mode Orange How to display DVR information On Screen DisplayOSD‰ Live Mode Black ‰ Mouse context menuTo change display mode How to display each channel & multichannel DisplayHow to rotate monitoring channels Sequence To enable/disable sequence modeHow to record audio How to hide monitoring channels for privacyHow to turn sound On /Off Mute To turn sound on/offHow to record monitoring channels How to playback recorded video Normal Search ‰ To toggle between monitoring mode and playback modeFunction Remote Controller Front Panel USE Mouse ‰ Smart Search How to search recorded video Advanced Search‰ Statistics Search Show Motion DetectionHow to backup recorded video ‰ Event SearchHow to connect & control PTZ PTZ Mode‰ SET Preset ‰ Move Preset‰ Clear Preset ‰ ZoomHow to connect RS-232 port How to use alarm input & alarm outputSensor Operation Enter ‰ InstallationRemote Viewer Overview ‰ Connection‰ Status ‰ Setup‰ Audio Setup ‰ PTZ ControlDVR Remote Viewer Playback & Backup ‰ Sequence & Display ModeStatistics Mode Smart Search Mode Event Search Mode ‰ HOW to Backup Setup Menu Diagram Basic Setting Internet & Network DisplayHow to move the Setup menus PasswordUSE DAY Time Image Quality REC Mode RES Basic SettingSetting Recording ScheduleCamera Registration AudioHDD Hard Disk Drive PRE-POST RecordingNetwork Connection Service Port & DdnsInternet & Network Static IPUpdate Server Display ‰ Set ADJUSTMENT, OSD and Sequence in DisplayAdjustment OSDInformation & Update SystemSequence DATE/TIME System LOGServer Password & Parameter PasswordShutdown Parameter Notification Technical SettingEvent To E-MAILRemote Controller Alarm InputMotion Alarm Output CH / Quality‰ How to use DVR ID ETCSpecifications Troubleshootingfaq Network DVR