JVC LPT1092-001A manual Only, On-Disc Timer Programming DVD Deck, Satellite Receiver Users

Press DVD so that the DVD lamp lights up on the unit.

32 EN TIMER RECORDING

	On-Disc Timer Programming (DVD Deck		● Each press of rt advances/goes back the start time in 1-min.
			increments.
	Only)		● To advance/go back the start time in 30-min. increments, press and
			hold rt.
			7 Press w e to select “STOP”, then press rt to set the desired
			stop time.
			● Each press of rt advances/goes back the stop time in 1-min.
			increments.
On-Disc Timer Programming is a function used with discs that are			● To advance/go back the stop time in 30-min. increments, press and
			hold rt.
especially intended for a specific programme. The disc is then			8 Press w e to select “TV PROG”, then press rt to select the
programmed for a programme you always watch every day or			desired channel.
every week. Since older programmes are automatically
			9 Set “DAILY/WEEKLY” option.
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
without worrying about how much recording capacity remains.			● Refer to step 6 in “SHOWVIEW™ Timer Programming” ( pg. 29).
			● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
( pg. 33)
			Programming. ( pg. 30, “Weekly/Daily Recording”)
You can programme each disc to timer-record as many as
			10 Set the other recording options as required.
8 programmes.
			● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
● Make sure that the unit’s built-in clock is set properly.			However, you cannot select FR (JUST), FR60–FR360 and FR420.
● Turn on the unit.			● Refer to step 6 in “SHOWVIEW™ Timer Programming” ( pg. 29).
● Turn on the TV and select the AV mode.			● It is not possible to use the Free Rate function. ( pg. 62)
● Slide the TV/DVD switch to DVD.			11 Press ENTER to access the Programme Confirmation screen.
			12 Press ENTER to complete timer programming.
ATTENTION:			● To programme another timer, repeat steps 3 – 12.
● On-Disc Timer Programming is possible only with the disc for On-
		Disc Timer Programming.	Satellite Receiver Users
● If data is recorded on a disc for On-Disc Timer Programming using			To timer-record a satellite broadcast using the On-Disc Timer
		a unit from another manufacturer, On-Disc Timer Programming	Programming function:
		may no longer function properly.	A Perform “On-Disc Timer Programming (DVD Deck Only)”.
			B Set the satellite receiver to the appropriate channel before
			the selected programme begins.
			C Select “L-2” in step 8.
			D Leave the satellite receiver’s power on.

DVD

To Timer-record The Programme With The Programmed Disc

1 Load a programmed disc.

2 Press TIMER #. The unit turns off and “” appears on the front display panel. The DVD timer indicator also lights up on the unit and the unit is automatically turned off.

●To disengage the timer mode, press TIMER # again.

NOTES:

PROG ENTER

TIMER

● On-Disc Timer Programming is not possible on a DVD-RW disc

formatted in video mode. ( pg. 89)

● The information of a programme recorded with On-Disc Timer

Programming is not stored in the library. ( pg. 71)

rtwe

To Make The Disc For On-Disc Timer Programming

1 Load a recordable disc.

2

3 Press PROG to access the Programme Check screen.

4 When On-Disc Timer Programming is made for the first time on the disc

Press rt to select “DISC TIMER PRGM”, then press ENTER.

●When some programmes are recorded on the disc, a caution message appears. In such a case, backup the programmes as required, then format the disc before making On-Disc Timer Programming. ( pg. 89)

When On-Disc Timer Programming has already been made on the disc

Press rt to select “NEW TIMER PROGRAMME”, then press

ENTER.

5 Press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

● The play list is not created for the programmes recorded with On-Disc

Timer Programming. ( pg. 68)

● Basic Recording ( pg. 26), SHOWVIEW Timer Programming

( pg. 29), Manual Timer Programming ( pg. 31) are not possible

on the On-Disc Timer programmed disc.

● The beginning of a programme may not be recorded. Also, if the 1st

programme’s recording stop time and the 2nd programme’s recording

start time is the same, the ending of the 1st programme may not be

recorded.

● If there is a power cut while recording, the recordings before the

power cut are not guaranteed.

6 Press w e to select “START”, then press rt to set the desired start time.