Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the unit’s [L-2 IN/DECODER] connector.
1Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” ( pg. 44).
2Press rt to select “L-2 SELECT”, then press ENTER.
3 Press rt to select the appropriate setting, then press
ENTER. | | | | | | | |
| MONITOR TYPE | | | 4:3LB | | |
4 Press SET UP to complete the | | | | | | | | |
| F-1 INPUT | | | | VIDEO | | |
| | | | | | | |
| L-1 INPUT | | | | VIDEO | | |
setting. | | | | | | | |
| L-1 OUTPUT | | SCART VIDEO | | |
| | | | | | | | |
NOTES: | | | | | | VIDEO/RGB | |
| L-2 SELECT | | | S-VIDEO/RGB | |
| | | | | |
| SET UP | OK | | | SAT VIDEO/RGB | | |
● If “L-2 SELECT” is set to | SELECT | WITH [CURSORS] | | |
| | | | | DECODER | |
EXIT | SELECT | THEN PRESS [ENTER] | |
“S-VIDEO/RGB”, it is not possible | | | | | |
| | | | | | | |
to output colour signals correctly from the VHS deck.
●If “L-2 SELECT” is set to “DECODER”, only the DVD deck operates properly.
* The boldface settings below indicate the settings at your purchase.
8L-2 SELECT — VIDEO/RGB / S-VIDEO/RGB /
SAT VIDEO/RGB / DECODER
Select “VIDEO/RGB” or “S-VIDEO/RGB” to use this unit as the recording deck with the player connected to the [L-2 IN/ DECODER] connector, or to use the satellite receiver connected to the [L-2 IN/DECODER] connector.
VIDEO/RGB: If a connected appliance’s output is compatible with regular video signals, set to “VIDEO/RGB”.
S-VIDEO/RGB: If a connected appliance’s output is compatible with Y/C signals, set to “S-VIDEO/RGB”. You can obtain high-quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)
Select “SAT VIDEO/RGB” to view a satellite programme with the TV set while the unit is turned off. ( pg. 76)
SAT VIDEO/RGB: If a connected satellite receiver’s output is compatible with regular video signals, set to “SAT VIDEO/RGB”.
DECODER: To use a decoder connected to the [L-2 IN/DECODER] connector.
NOTES:
●If you have a satellite receiver or a decoder connected to the [L-2 IN/ DECODER] connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.
●If you are not connecting a satellite receiver or a decoder to the [L-2 IN/DECODER] connector, leave “L-2 SELECT” set to “VIDEO/RGB”.
●When “L-2 SELECT” is set to “SAT VIDEO/RGB”, “SAT” appears on the TV screen or front display panel instead of “L-2”.
●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT VIDEO/RGB”.
●If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2 SELECT” to “DECODER”.
●If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT VIDEO/RGB” or “DECODER”, be sure to connect the [L-1 IN/OUT] connector with a TV.
●If “L-2 SELECT” is set to “S-VIDEO/RGB”, the monochrome signal is output from VHS deck. Be sure to select setting other than “S-VIDEO/RGB” when you use the VHS deck.
Set “F-1 INPUT” to the appropriate mode depending on the connector ([VIDEO] or [S-VIDEO]) being used on the front panel.
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” ( pg. 44).
2Press rt to select “F-1 INPUT”, then press ENTER.
3 Press rt to select the appropriate setting, then press
ENTER. | MONITOR TYPE | 4:3LB |
4 Press SET UP to complete the | F-1 INPUT | | VIDEO |
L-1 INPUT | | VIDEO |
setting. | | S-VIDEO |
L-1 OUTPUT | SCART VIDEO |
| L-2 SELECT | VIDEO/RGB |
* The boldface settings below | SET UP | OK | SELECT WITH [CURSORS] |
indicate the settings at your | EXIT | SELECT | THEN PRESS [ENTER] |
|
purchase.
8F-1 INPUT — VIDEO / S-VIDEO
VIDEO: When connecting an appliance to the [VIDEO] input connector, set to “VIDEO”.
S-VIDEO: When connecting an appliance to the [S-VIDEO] input connector, set to “S-VIDEO”.
NOTE:
If “F-1 INPUT” is set to “S-VIDEO”, the monochrome signal is output from VHS deck. Be sure to select “VIDEO” when you use the VHS deck.
