JVC HR-XV3E 12 EN, Perform Preset Download, Set the video channel, On the on-screen display

Page 12

12 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

If you have connected the unit to your TV via the AV connection ( pg. 9), the unit will automatically perform Preset Download instead of the Auto Set Up in step D on page 11. After downloading, the unit sets the clock and Guide Program numbers automatically.

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link or DATA LOGIC via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

●Slide the TV/VCR/DVD switch to the right.

●Perform steps A to C of “Auto Set Up” on page 10 before continuing.

NOTES:

●For details, refer to the instruction manual of your TV.

●In areas where no TV station transmits a PDC (Programme Delivery Control) signal, the unit can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or SET UP MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the unit power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this unit, the characters available for station names (ID) are

A–Z, 0–9, –, f, + and I (space). Some names of downloaded stations may differ from those of your TV. ( pg. 71)

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or e.

Preset positions on the front display panel increase from “CH 1”; do NOT press any button on the unit or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 13.

●If you are using the on-screen display, the T-V LINK screen

will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the unit or remote control while

downloading is in progress, it will be interrupted.

B Set the video channel.

Set the video channel to off manually. ( pg. 73)

After “Preset Download” is completed, perform “Monitor Set (DVD deck)” on page 14.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HR-XV3E Safety Precautions Use only discs marked with the followingFor Italy Contents About Discs Playable DiscsUnplayable Discs Region NumberFile Structure of Discs Care and Handling of DiscsPlacing a Disc Place the discFront View Infrared Beam Receiving Window M Front Display Panel pgMode Display L-1, L-2, F-1 or SAT DVD Mode Indicator Tape Remaining Time Indicator  pgCassette Loaded Mark On the tape BeginningEndRemote Control How To UseCheck the contents Basic ConnectionsSituate the unit Connect the unit to TVAuto Set Up 10 ENTurn on the unit Select your countryPerform Auto Set Up Confirm/Set video channelOn the front display panel Press rt to select Auto and press OK or ePreset Download Perform Preset Download12 EN Set the video channelLink Functions 14 EN Monitor SetDVD deck Access the Country Set screen Press VCR so that the VCR indicator lights upLanguage Select the VHS deckAccess the DVD Set Up menu screen 16 ENLanguage Press rt to move H to on Screen LANGUAGE, then press OKLanguage Code List 18 EN Basic PlaybackPlayback Features 20 EN Instant ReViewRepeat Playback Manual TrackingBasic Recording Recording Features Instant Timer Recording ITR22 EN Tape Remaining TimeReceiving Stereo and Bilingual Programmes PlaybackRecording Showview Timer Programming 24 ENEngage the unit’s timer mode VPS/PDC RecordingSatellite Receiver Users Repeat steps B G for each additional programmeExpress Timer Programming 26 ENDisengage the timer mode Access the Programme Check screenCancel or change a programme Return to the timer modeCancel or change programme setting 28 ENSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeBefore performing the following steps Set L-2 Select to A/V or SAT.  pg30 EN Load the discPause playback Locating a desired scene using the DVD menu Access the PBC menuAccess the DVD menu Locating the start point of the item or skip the item32 EN Resume FunctionMemorize a resume point Resume playbackAccess the selection menu Zooming 3D PhonicSelect the effect level VFP function Adjusting the picture quality 34 ENAccess the on-screen bar Select the optionSelect the repeat mode 36 ENChange the time information Select the menu itemAccess the repeat mode When using the Repeat buttonTo cancel A-B Repeat Playback Select the start point38 EN Time SearchChapter Search To clear the programme table Press Play Setup Programme PlaybackSelect the tracks in the desired order Access the menu 40 ENRandom Playback Subtitle SelectionAngle Selection Select the view anglePress Angle 32/33/3Back to the beginningWhen using the A.MONITOR button Audio Language SelectionSelect the audio language Press A.MONITORAudio Channel Selection Select the audio channelFor Video CD For Svcd44 EN Parental LockTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 46 ENPage What is MP3? 48 ENAbout MP3 Disc MP3 control displayUsing the MP3 control display MP3 PlaybackSelect the group Press w e to select the desired group50 EN Group/track selectionTo start playback by specifying the group/track number To return to the MP3 control displayWhat is JPEG? About Jpeg DiscJpeg control display Using the Jpeg control display 52 ENJpeg Playback Press rt to select the desired file, then press OK orGroup/file selection ZoomingTo return to the Jpeg control display 54 EN Set the input mode of recording deck Engage the Record Pause mode of the recording deckStart the source player Start the recording deck56 EN DubbingFrom DVD to VHS Select the input mode Place a disc and load an MDPrepare the audio device for dubbing For the digital audio device58 EN TV Multi-Brand Remote Control Set the TV brand codeOperate the TV 01, 23, 24Connecting To a Satellite Receiver 60 ENSimple Connections Perfect ConnectionsSelect the input mode Make connectionsConnect the decoder Set the tunerMode Set VHS deck Access the Main Menu screenAccess the Mode Set screen 62 ENWhen you use the Direct Rec function, be sure to use a TV For Example64 EN About Ntsc PlaybackMode Set DVD deck For each mode setting, see pages 66 toOthers Press rt to move H to RESUME, then press OKPicture Settings Audio Settings66 EN Video Normal / Video Active / Film / AutoOthers Settings Playback discsDigital Audio CD/Video CD68 EN Tuner SetAuto Channel Set Perform Auto Channel SetManual Channel Set When Receiving a Scrambled Broadcast 70 ENDelete a Channel Set Stations a Set Stations B72 EN TV Station And ID ListAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set Set the RF output system74 EN Clock SetYou can disable the unit’s operation Child LockSet the Child Lock 76 EN Tape Transport VHS deckPlayback VHS deck Playback DVD deckMP3 Playback DVD deck Jpeg Playback DVD deckRecording VHS deck Scene is not recorded from multiple anglesTimer Recording VHS deck 78 ENPAL DVD80 EN Operations on VHS Deck Link82 EN Page HR-XV3E
Top Page Image Contents