JVC HR-XV3E manual 28 EN, Select the programme to modify, Cancel or change programme setting

Page 28

28 EN

OPERATIONS ON VHS DECK (cont.)

When programmes overlap each other

If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. The Programme Check screen appears and conflicting programmes will start blinking.

Example: Programme 1 (you have just made) and Programme 4 overlap each other.

A Confirm the overlapping programmes.

Overlapping programmes blink on the TV screen.

B Select the programme to modify.

Press rt, then press OK or e.

●You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press PROG to finish the timer programme setting. The programme with the lower programme number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the unit will return to the normal screen.

C Cancel or change programme setting.

To cancel a programme, press & when the Programme screen you do not want is shown. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

To change a programme, press the appropriate button: START +/–,STOP +/–,DATE +/–,PR +/–,VPS/PDC (number key “7”), DAILY (number key “8”), WEEKLY (number key “9”) and/or p when the Programme screen on which you want to make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

NOTE:

If the overlap is not yet solved, or another overlap occurs with the timer programme setting after making the last correction on a programme, the conflicting programmes will be shown on the Programme Check screen again. Repeat the above steps again until the overlap is solved.

Automatic Satellite Programme Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the unit’s L-2 IN/DECODER connector and programme the timer on the satellite receiver. The unit starts or stops recording by the signals input from the satellite receiver. After recording, the unit’s power shuts off automatically.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the unit will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the L-2 IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the unit will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer- recording cannot be done at the same time.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents HR-XV3E Use only discs marked with the following Safety PrecautionsFor Italy Contents About Discs Playable DiscsUnplayable Discs Region NumberFile Structure of Discs Care and Handling of DiscsPlacing a Disc Place the discFront View Infrared Beam Receiving Window M Front Display Panel pgMode Display L-1, L-2, F-1 or SAT DVD Mode Indicator Tape Remaining Time Indicator  pgCassette Loaded Mark On the tape BeginningEndRemote Control How To UseCheck the contents Basic ConnectionsSituate the unit Connect the unit to TVAuto Set Up 10 ENTurn on the unit Select your countryPerform Auto Set Up Confirm/Set video channelOn the front display panel Press rt to select Auto and press OK or ePreset Download Perform Preset Download12 EN Set the video channelLink Functions Monitor Set 14 ENDVD deck Access the Country Set screen Press VCR so that the VCR indicator lights upLanguage Select the VHS deckAccess the DVD Set Up menu screen 16 ENLanguage Press rt to move H to on Screen LANGUAGE, then press OKLanguage Code List 18 EN Basic PlaybackPlayback Features 20 EN Instant ReViewRepeat Playback Manual TrackingBasic Recording Recording Features Instant Timer Recording ITR22 EN Tape Remaining TimePlayback Receiving Stereo and Bilingual ProgrammesRecording Showview Timer Programming 24 ENEngage the unit’s timer mode VPS/PDC RecordingSatellite Receiver Users Repeat steps B G for each additional programmeExpress Timer Programming 26 ENDisengage the timer mode Access the Programme Check screenCancel or change a programme Return to the timer modeCancel or change programme setting 28 ENSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeBefore performing the following steps Set L-2 Select to A/V or SAT.  pgLoad the disc 30 ENPause playback Locating a desired scene using the DVD menu Access the PBC menuAccess the DVD menu Locating the start point of the item or skip the item32 EN Resume FunctionMemorize a resume point Resume playbackZooming 3D Phonic Access the selection menuSelect the effect level VFP function Adjusting the picture quality 34 ENAccess the on-screen bar Select the optionSelect the repeat mode 36 ENChange the time information Select the menu itemAccess the repeat mode When using the Repeat buttonTo cancel A-B Repeat Playback Select the start pointTime Search 38 ENChapter Search Programme Playback To clear the programme table Press Play SetupSelect the tracks in the desired order Access the menu 40 ENRandom Playback Subtitle SelectionAngle Selection Select the view anglePress Angle 32/33/3Back to the beginningWhen using the A.MONITOR button Audio Language SelectionSelect the audio language Press A.MONITORAudio Channel Selection Select the audio channelFor Video CD For Svcd44 EN Parental LockTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 46 ENPage What is MP3? 48 ENAbout MP3 Disc MP3 control displayUsing the MP3 control display MP3 PlaybackSelect the group Press w e to select the desired group50 EN Group/track selectionTo start playback by specifying the group/track number To return to the MP3 control displayAbout Jpeg Disc What is JPEG?Jpeg control display Using the Jpeg control display 52 ENJpeg Playback Press rt to select the desired file, then press OK orZooming Group/file selectionTo return to the Jpeg control display 54 EN Set the input mode of recording deck Engage the Record Pause mode of the recording deckStart the source player Start the recording deckDubbing 56 ENFrom DVD to VHS Select the input mode Place a disc and load an MDPrepare the audio device for dubbing For the digital audio device58 EN TV Multi-Brand Remote Control Set the TV brand codeOperate the TV 01, 23, 24Connecting To a Satellite Receiver 60 ENSimple Connections Perfect ConnectionsSelect the input mode Make connectionsConnect the decoder Set the tunerMode Set VHS deck Access the Main Menu screenAccess the Mode Set screen 62 ENWhen you use the Direct Rec function, be sure to use a TV For Example64 EN About Ntsc PlaybackMode Set DVD deck For each mode setting, see pages 66 toOthers Press rt to move H to RESUME, then press OKPicture Settings Audio Settings66 EN Video Normal / Video Active / Film / AutoOthers Settings Playback discsDigital Audio CD/Video CD68 EN Tuner SetAuto Channel Set Perform Auto Channel SetManual Channel Set 70 EN When Receiving a Scrambled BroadcastDelete a Channel Set Stations a Set Stations B72 EN TV Station And ID ListAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set Set the RF output system74 EN Clock SetChild Lock You can disable the unit’s operationSet the Child Lock 76 EN Tape Transport VHS deckPlayback VHS deck Playback DVD deckMP3 Playback DVD deck Jpeg Playback DVD deckRecording VHS deck Scene is not recorded from multiple anglesTimer Recording VHS deck 78 ENPAL DVD80 EN Operations on VHS Deck Link82 EN Page HR-XV3E
Top Page Image Contents