JVC HR-XV3E manual 34 EN, VFP function Adjusting the picture quality

Page 34

34 EN

OPERATIONS ON DVD DECK (cont.)

To adjust picture appearance manually

3Access the USER menu.

Press w e repeatedly to select “USER 1” or “USER 2”.

USER 1

GAMMA +0

BRIGHTNESS +0

CONTRAST +0

SATURATION +0

TINT+0

SHARPNESS +3

Y DELAY +0

VFP function

— Adjusting the picture quality

The VFP (Video Fine Processor) function enables you to adjust the picture character according to the type of programming, picture tone or personal preference.

NOTE:

Before you start operation;

The VFP setting screen disappears if no operations are done for more than about 10 seconds. If the setting screen disappears before you finish, start from step 1 again.

1Access the VFP setting menu.

Press DVD PICTURE during
Press DVD PICTURE during
playback.		NORMAL
● The current setting appears on		GAMMA	+0
● The current setting appears on		BRIGHTNESS +0
the TV screen.		CONTRAST	+0
		SATURATION	+0
		TINT	+0
		SHARPNESS	+3
		Y DELAY	+0

2Select the VFP mode.

Press w e repeatedly.

●Each time you press w e, the VFP mode changes as follows:

NORMAL]CINEMA]USER 1]USER 2](Back to the beginning)

NORMAL: Select this normally.

CINEMA: Suitable for movie.

USER 1/ You can adjust parameters that affect picture

USER 2: appearance and store settings. Go to step 3.

NOTE:

4Select the parameter.

Press rt repeatedly to select a parameter you want to adjust, then press OK.

●Adjust gradually and confirm picture appearance results are as preferred.

GAMMA	Controls brightness of neutral tints while
(–4 to +4):	maintaining brightness of dark and bright
	portions.
BRIGHTNESS	Controls screen brightness.
(–16 to +16):
CONTRAST	Controls screen contrast.
(–16 to +16):
SATURATION	Controls screen colour depth.
(–16 to +16):
TINT	Controls screen tint.
(–16 to +16):
SHARPNESS	Controls screen sharpness.
(+0 to +3):
Y DELAY	Controls screen colour gap.
(–2 to +2):

●VFP menu disappears and the following pop-up window appears on the TV screen.

GAMMA +0

GAMMA +0

5Adjust the parameter.

Press rt repeatedly to change the setting, then press

OK.

●The current VFP settings appear again.

6Adjust the other parameters.

Repeat steps 4 and 5 to adjust other parameters.

To return to the normal screen

Press DVD PICTURE.

To activate your setting

Press DVD PICTURE, then press w e repeatedly to select “USER 1” or “USER 2” that you have changed the parameters.

You cannot adjust the parameters of “NORMAL” and “CINEMA”.

Image 34

Contents HR-XV3E Use only discs marked with the following Safety PrecautionsFor Italy Contents Unplayable Discs About DiscsPlayable Discs Region NumberPlacing a Disc File Structure of DiscsCare and Handling of Discs Place the discFront View Infrared Beam Receiving Window M Front Display Panel pgCassette Loaded Mark Mode Display L-1, L-2, F-1 or SAT DVD Mode IndicatorTape Remaining Time Indicator pg On the tape BeginningEndRemote Control How To UseSituate the unit Check the contentsBasic Connections Connect the unit to TVTurn on the unit Auto Set Up10 EN Select your countryOn the front display panel Perform Auto Set UpConfirm/Set video channel Press rt to select Auto and press OK or e12 EN Preset DownloadPerform Preset Download Set the video channelLink Functions Monitor Set 14 ENDVD deck Language Access the Country Set screenPress VCR so that the VCR indicator lights up Select the VHS deckLanguage Access the DVD Set Up menu screen16 EN Press rt to move H to on Screen LANGUAGE, then press OKLanguage Code List 18 EN Basic PlaybackPlayback Features Repeat Playback 20 ENInstant ReView Manual TrackingBasic Recording 22 EN Recording FeaturesInstant Timer Recording ITR Tape Remaining TimePlayback Receiving Stereo and Bilingual ProgrammesRecording Showview Timer Programming 24 ENSatellite Receiver Users Engage the unit’s timer modeVPS/PDC Recording Repeat steps B G for each additional programmeExpress Timer Programming 26 ENCancel or change a programme Disengage the timer modeAccess the Programme Check screen Return to the timer modeSelect the programme to modify Cancel or change programme setting28 EN Overlapping programmes blink on the TV screenBefore performing the following steps Select the L-2 Select modeRecording mode Set L-2 Select to A/V or SAT. pgLoad the disc 30 ENPause playback Access the DVD menu Locating a desired scene using the DVD menuAccess the PBC menu Locating the start point of the item or skip the itemMemorize a resume point 32 ENResume Function Resume playbackZooming 3D Phonic Access the selection menuSelect the effect level VFP function Adjusting the picture quality 34 ENAccess the on-screen bar Select the optionChange the time information Select the repeat mode36 EN Select the menu itemTo cancel A-B Repeat Playback Access the repeat modeWhen using the Repeat button Select the start pointTime Search 38 ENChapter Search Programme Playback To clear the programme table Press Play SetupSelect the tracks in the desired order Random Playback Access the menu40 EN Subtitle SelectionPress Angle Angle SelectionSelect the view angle 32/33/3Back to the beginningSelect the audio language When using the A.MONITOR buttonAudio Language Selection Press A.MONITORFor Video CD Audio Channel SelectionSelect the audio channel For Svcd44 EN Parental LockTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 46 ENPage About MP3 Disc What is MP3?48 EN MP3 control displaySelect the group Using the MP3 control displayMP3 Playback Press w e to select the desired groupTo start playback by specifying the group/track number 50 ENGroup/track selection To return to the MP3 control displayAbout Jpeg Disc What is JPEG?Jpeg control display Jpeg Playback Using the Jpeg control display52 EN Press rt to select the desired file, then press OK orZooming Group/file selectionTo return to the Jpeg control display 54 EN Start the source player Set the input mode of recording deckEngage the Record Pause mode of the recording deck Start the recording deckDubbing 56 ENFrom DVD to VHS Prepare the audio device for dubbing Select the input modePlace a disc and load an MD For the digital audio device58 EN Operate the TV TV Multi-Brand Remote ControlSet the TV brand code 01, 23, 24Simple Connections Connecting To a Satellite Receiver60 EN Perfect ConnectionsConnect the decoder Select the input modeMake connections Set the tunerAccess the Mode Set screen Mode Set VHS deckAccess the Main Menu screen 62 ENWhen you use the Direct Rec function, be sure to use a TV For Example64 EN About Ntsc PlaybackOthers Mode Set DVD deckFor each mode setting, see pages 66 to Press rt to move H to RESUME, then press OK66 EN Picture SettingsAudio Settings Video Normal / Video Active / Film / AutoDigital Others SettingsPlayback discs Audio CD/Video CDAuto Channel Set 68 ENTuner Set Perform Auto Channel SetManual Channel Set 70 EN When Receiving a Scrambled BroadcastDelete a Channel Set Stations a Set Stations B72 EN TV Station And ID ListVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode Set the RF output system74 EN Clock SetChild Lock You can disable the unit’s operationSet the Child Lock Playback VHS deck 76 ENTape Transport VHS deck Playback DVD deckRecording VHS deck MP3 Playback DVD deckJpeg Playback DVD deck Scene is not recorded from multiple anglesTimer Recording VHS deck 78 ENPAL DVD80 EN Operations on VHS Deck Link82 EN Page HR-XV3E