Honeywell XYR 5000 LINE manual Revision Notes, Contacts, Telephone

Page 4

About This Document

Revision Notes

The following list provides notes concerning all revisions of this document.

Doc ID	Rel ID	Date	Notes

34-XY-25-05	Rlse. 0	12/03	1st issue of document.

34-XY-25-05	Rev. 1	02/04	2nd issue of document.

34-XY-25-05	Rev. 2	06/04	Reformatted layout, updated technical information.

34-XY-25-05	Rev. 3	05/05	Updated Modbus Info.

34-XY-25-05	Rev. 4	08/06	Updated for version 1.70 software release.

Contacts

World Wide Web

The following lists Honeywell’s World Wide Web sites that will be of interest to our industrial automation and control customers.

Honeywell Organization	WWW Address (URL/e-mail)

Corporate	http://www.honeywell.com

Industrial Measurement and Control	http://content.honeywell.com/imc/

International	http://www.honeywell.com/Business/global.asp

Field Instruments	http://www.honeywell.com/imc

Technical Assistance Center	ACE@Honeywell.com(e-mail)

Telephone

Contact us by telephone at the numbers listed below.

	Organization	Phone Number

United States and Canada	Honeywell Inc.	1-800-343-0228	Sales
	Industrial Automation and Control	1-800-525-7439	Service
	Global Technical Support Center	1-800-423-9883

Asia Pacific	Honeywell Asia Pacific Inc.	(852) 8298298
	Hong Kong

Europe	Honeywell PACE	[32-2] 728-2111
	Brussels, Belgium

Latin America	Honeywell Inc.	(305) 364-2355
	Sunrise, Florida U.S.A.

IV

Image 4

Contents Base Radio User Guide XYR 5000 Line 34-XY-25-05 Rev 08/06Page Base Radio FCC CertificationContacts Revision NotesTelephone Table of Contents Quare R OOT F Unction Overall Wiring Schematic Table of FiguresIntroduction Using this ManualAbout the Device Unpacking Software CompatibilityOverall Wiring Schematic Quick StartPage Mechanical Installation InstallationBase Radio Positioning General Layout Electrical Installation Electrical SpecificationsTerminal Block Labels Wiring Power to the Base Radio Wiring RS-485 to the Base RadioWiring the RS-485/232 Converter to the Base Radio Wiring RS-485 to the Base RadioWiring the RS-485/USB Converter to the Base Radio USB Driver InstallationDaisy-Chaining Multiple Base Radios to Single RS-485/Power Wiring the DB-9 RS-485 Cable to the Base RadioUSB Converter’s Male DB-9 Connector USB Driver Un-installationDaisy-Chaining Power to Multiple Base Radios Daisy-Chaining RS-485 to Multiple Base RadiosTerminating Communications Wiring to the Base Radio Daisy-Chaining RS-485 to Multiple Base RadiosGrounding the Base Radio High Gain AntennaBase Radio Displayed Messages General ConfigurationRead Only Sequence Overall Configuration Menu Map Read Only SequenceSetting the User Password Menu Map to Password SettingConfiguring the RF Communications RF Channel SelectionMenu Map to RF Baud Rate Setting RF Baud Rate SelectionHigh RF ID Setting High Rfid SettingBase Radio Setup Modbus Baud Rate SettingModbus Device ID Setting Menu Map to Modbus Baud Rate SettingPage Modbus Parity Setting Modbus Mapping Mode SettingModbus Communication Protocol RegmodeCommand 03-Read Holding Registers Modbus CommandsCommand 08- Diagnostic Command 12- Get Com Event Log Command 11- Get Com Event CounterCommand 17- Report Slave ID Command 43- Read Device ID Base Radio Holding RegistersRegister Address Description Register Type Register Address DescriptionBase Radio Device Type Registers Base Radio Device Status RegistersBase Radio On/Offline Transmitter Registers Value Base Radio Device StatusDevice ID Mapping Mode Register Mapping ModeTransmitter Holding Registers Register AddressTransmitter Device Type Holding Registers Value Device TypeAlarm Condition WN571 only Square Root FunctionTransmitter Device Status Registers Value Transmitter Device StatusTechnical Specifications Overall Base Radio Dimensions Appendix a Navigating the Menus Appendix B Base Radio Menu Map Figure A- 1 Base Radio Menu MapAppendix C Modbus Register Definitions Page Page Page Honeywell