Honeywell XYR 5000 LINE manual Unpacking, Software Compatibility

Page 9

The Honeywell Base Radio may be used to communicate with many Transmitters in various applications. You can use this device for long-term monitoring in remote locations, for short-term data gathering on process conditions, or to quickly test the economic viability of a new installation.

The purpose of this guide is to help you install, configure and maintain your Honeywell Base Radio.

1.3Unpacking

Remove the Packing List and check off the actual equipment received. If you have any questions about your shipment, please call your Honeywell Representative. Upon receipt of shipment, inspect the container for any signs of damage in transit. Especially take note of any evidence of rough handling. Report any apparent damage immediately to the shipping agent.

Please note that sometimes units are assembled with accessories when shipped. Inspect the shipment carefully if you think that something is missing. This is rare, as we take considerable care to pack units for shipment, but it does sometimes happen. Please give us a call and we may be able to resolve this matter quickly over the phone.

Please note that the carrier will not honor any claims for damage unless all shipping materials are saved for their examination. If you find any damage while you are examining and removing the contents, save the packing material and the carton.

1.4Software Compatibility

Software for Honeywell is revised periodically. Internal device software may contain portions that are not compatible with previous versions of WMT (Wireless Management Toolkit software)

To ensure software compatibility, WMT version 1.70.138 or later must be used. If you believe you are experiencing software compatibility issues please call Honeywell Technical Support at 800-423-9883 or email ACE@Honeywell.com.

2

Image 9

Contents XYR 5000 Line 34-XY-25-05 Rev 08/06 Base Radio User GuidePage FCC Certification Base RadioRevision Notes ContactsTelephone Table of Contents Quare R OOT F Unction Table of Figures Overall Wiring SchematicUsing this Manual IntroductionAbout the Device Software Compatibility UnpackingQuick Start Overall Wiring SchematicPage Installation Mechanical InstallationBase Radio Positioning General Layout Electrical Specifications Electrical InstallationTerminal Block Labels Wiring RS-485 to the Base Radio Wiring Power to the Base RadioWiring RS-485 to the Base Radio Wiring the RS-485/232 Converter to the Base RadioUSB Driver Installation Wiring the RS-485/USB Converter to the Base RadioWiring the DB-9 RS-485 Cable to the Base Radio Daisy-Chaining Multiple Base Radios to Single RS-485/PowerUSB Converter’s Male DB-9 Connector USB Driver Un-installationDaisy-Chaining RS-485 to Multiple Base Radios Daisy-Chaining Power to Multiple Base RadiosDaisy-Chaining RS-485 to Multiple Base Radios Terminating Communications Wiring to the Base RadioHigh Gain Antenna Grounding the Base RadioGeneral Configuration Base Radio Displayed MessagesRead Only Sequence Read Only Sequence Overall Configuration Menu MapMenu Map to Password Setting Setting the User PasswordRF Channel Selection Configuring the RF CommunicationsRF Baud Rate Selection Menu Map to RF Baud Rate SettingHigh Rfid Setting High RF ID SettingModbus Baud Rate Setting Base Radio SetupMenu Map to Modbus Baud Rate Setting Modbus Device ID SettingPage Modbus Mapping Mode Setting Modbus Parity SettingRegmode Modbus Communication ProtocolModbus Commands Command 03-Read Holding RegistersCommand 08- Diagnostic Command 11- Get Com Event Counter Command 12- Get Com Event LogCommand 17- Report Slave ID Base Radio Holding Registers Command 43- Read Device IDRegister Address Description Register Type Register Address DescriptionBase Radio Device Status Registers Base Radio Device Type RegistersBase Radio On/Offline Transmitter Registers Value Base Radio Device StatusRegister Mapping Mode Device ID Mapping ModeTransmitter Holding Registers Register AddressValue Device Type Transmitter Device Type Holding RegistersSquare Root Function Alarm Condition WN571 onlyTransmitter Device Status Registers Value Transmitter Device StatusTechnical Specifications Overall Base Radio Dimensions Appendix a Navigating the Menus Figure A- 1 Base Radio Menu Map Appendix B Base Radio Menu MapAppendix C Modbus Register Definitions Page Page Page Honeywell