Kathrein UFS 702sw, UFS 702si manual LNB settings, Path MENUMain menuInstallationLNB

Page 44

Installation

VCR record

The VCR Scart socket has two different modes for automatic VCR recording with the timer function: Standard The video signal (pin 19 on VCR Scart socket)

to the VCR is always available.

Pin 8 on the VCR Scart socket (switching voltage) is switched as an input, meaning that when you press the playback button on your video recorder, your satellite receiver automatically switches the video and audio signals coming from the video recorder to the TV Scart socket via the VCR Scart socket and from there to the TV set.

For timer-controlled video recordings in standard mode you must enter identical start and end times on your video recorder and in the “Timer Programming” menu.

Sat Record The video output signal (pin 19) from the VCR is always available.

When a timer event is active i.e. when the unit switches to the channel to be recorded at the pre-programmed time,12 V is output at pin 8 of the VCR Scart socket.

A “Sat Record”-compatible video recorder detects this voltage and automatically switches to record.

When the timer recording is ﬁnished, pin 8 is switched back to input mode and is again ready to relay the VCR signal on playback.

LNB settings

	Path: MENU>Main menu>Installation>LNB
	{ON}	Default setting
	{OFF}	Operation without LNB signal (e.g. on special
		multi-subscriber systems)
In standby	{OFF}	Default setting
	On standalone systems only use the {OFF} setting, otherwise
	the receiver will also supply power to the LNB in standby.
	This may cause the power consumption of the receiver to
	increase from the typical value of 2 Watts to as high as
	10 Watts in standby.
	{ON}	The LNB voltage remains switched on in
		standby e.g. to supply power in an appropriate
		multi-subscriber system.

44

Image 44

Contents

UFS 702sw/si Preface Important InformationContents Installation Audio settingsError detection/troubleshooting and service SatellitesSafety instructions important notes Receiver features View of rear panel Controls, displays and connectionsView of front panel ﬂap folded down LCD Display Important note on setting up receiver on a UFOmicro system Connecting the unit Reception system presetsConnection and set-up Reception requirementsInserting batteries into the remote control TV and Video recorder connectionAudio connection Dolby connectionRemote control Remote control RC Operating instructions Menu conceptMenu tree Language selection OSDError signalling On-Screen Displays OSDChannel information TV channel informationChannel hopping display Channel list TV/radioChannel selection Switch between TV/radio modeChannel selection using number buttons and & buttons Select last channel Favourites listEPG Electronic Programme Guide EPG Electronic Programme Guide Channels menu channel management Favourites list/channel arrangement move, delete, copy Path MENUMain menuChannelsChannels menu channel management Delete Channel menu channel managementMove Copy Move channel block Delete channel block Copy channel block copy from channel pool to favourites listChange names of favourites lists Channel poolPath MENUMain menuChannelsFavourites names Path MENUMain menuChannelsChannel poolAntenna signal and reception parameters button Delete one channel/all channels in channel poolParental control child lock/PIN Path MENUMain menuChannelsParental control LockTo change the PIN code To change the PIN, activate the PIN menu item with buttonPath MENUMain menuChannelsFavourites lists MENUMain menuChannelsChannel poolSearch Satellite searchTransponder search Path MENUMain menuSearchSatellites Path MENUMain menuSearchTransponderManual input for experts Path MENUMain menuSearchManualVideotext teletext Timer Manual Timer SettingAutomatic Timer Setting Deleting a Timer EventREc End HinweisEnter/change name SatellitesPath MENUMain menuSatellites OFF Enter LO1 Enter LO2Enter orbit position Enable Time offset Installation Path MENUMain menuInstallationTime offset Signal paths TV, VCR, picture format, record, digital audio Select character set factory setting LatinPath MENUMain menuInstallationSignal paths Language/character setVCR signals Picture formatDigital audio AC-3LNB settings Path MENUMain menuInstallationLNBDiSEqCTM Digital Satellite Equipment Control Various display time, RC, LCD, download, factory reset ResetPath MENUMain menuInstallationVarious Display time XxxxLCD display settings Time indicatorFactory reset Device settings Channels in favourites list 1 generalPerform factory reset on device settings 00000German LatinDownload-Over-Air Software update via satellite Restore channels in favourites lists 1OK = YES EX = no Playback Video recorder/PVR connectionRecording Return path Audio settings Setting the volumeDigital/analogue audio mode MutingAnalogue outputs AC 3 general Using the front panel Backup operationReceiver to receiver data transfer PreparationChannel list download Download operating systemTechnical features Technical appendixGeneral Additional featuresSoftware Update Type UFS 702si UFS 702sw SdramAccessories VHS/S-VHS switchingScart socket assignment VCR/AUXConnection example PVR VCRShort technical guide Channel packagePID Glossary Zapping VCR connectionViterbi rate Error detection/troubleshooting and service Problem Cause RemedyPRO SATSearch for new channels Channel change