Kathrein UFS 702si manual Error detection/troubleshooting and service, Problem Cause Remedy, Sat

Page 67

Error detection/troubleshooting and service

In the event of a malfunction, ﬁrst check all the cable connections and operating states:

1.Receiver and TV set power plugs are connected to wall socket

2.Antenna cables on receiver input

3.Receiver and TV set correctly connected by a Scart or cinch cable

4.Audio connections are made to Hi-Fi or Dolby Digital system as appropriate

5.Receiver and TV set (Hi-Fi/Dolby Digital system) are switched on (check power indicators)

6.Receiver is responding to remote control

A selection of troubleshooting tips is offered below.

Problem

Cause

Remedy

Consult an antenna specialist to have

Antenna signal of satellite

it checked and repaired as necessary.

“No signal!!” warning

reception system

missing

On “Installation” menu check LNB

appears on some or

or faulty. Incorrect oscillator

conﬁguration for satellite in question:

all channels

frequencies

set

in

LNB

High L.O. “10.600” GHz and Low

conﬁguration menu.

L.O. “9.750” GHz, and change as

necessary.

Receiver or remote control

Set infrared code 1, as described in

Remote

control

no

command

set

may

have

operating manual under “Remote

longer responding

been

unintentionally

control RC 660”; check batteries

changed

On “System set-up” - “Time set-up”

“Summer

Time”

setting

menu check “Summer Time enabled”

Wrong time

being

wrong. An

incorrect

time

and change as necessary. Switch off

displayed

was

imported

from

the

receiver at mains switch from current

reception signal

channel, wait 10 seconds and then

switch back on

The

following

channels

cut

out

DECT telephones operate

or

“Poor

signal

on the same

frequency

or

no

signal!!”

as

these

channels.

appears:

PRO

7,

Consult your antenna specialist

SAT

1,

Kabel

1,

Interference

may

occur

DSF, N 24, Tele 5,

due to inadequate level or

9 Live, HSE 24 and

poor shielding of cable

Sonnenklar TV

Black or blue screen,

Scart

connection

to

TV

Keep pressing the 0 button until the TV

no

on-screen

deactivated by accidentally

picture reappears on-screen

displays

pressing 0 button

67

Image 67

Contents UFS 702sw/si Important Information PrefaceContents Satellites InstallationAudio settings Error detection/troubleshooting and serviceSafety instructions important notes Receiver features View of front panel ﬂap folded down Controls, displays and connectionsView of rear panel LCD Display Important note on setting up receiver on a UFOmicro system Reception requirements Connecting the unitReception system presets Connection and set-upDolby connection Inserting batteries into the remote controlTV and Video recorder connection Audio connectionRemote control Remote control RC Menu concept Operating instructionsLanguage selection OSD Menu treeTV channel information Error signallingOn-Screen Displays OSD Channel informationChannel list TV/radio Channel hopping displayChannel selection using number buttons and & buttons Switch between TV/radio modeChannel selection Favourites list Select last channelEPG Electronic Programme Guide EPG Electronic Programme Guide Channels menu channel management Path MENUMain menuChannels Favourites list/channel arrangement move, delete, copyChannels menu channel management Move Channel menu channel managementDelete Copy Move channel block Copy channel block copy from channel pool to favourites list Delete channel blockPath MENUMain menuChannelsChannel pool Change names of favourites listsChannel pool Path MENUMain menuChannelsFavourites namesDelete one channel/all channels in channel pool Antenna signal and reception parameters button To change the PIN, activate the PIN menu item with button Parental control child lock/PINPath MENUMain menuChannelsParental control Lock To change the PIN codeMENUMain menuChannelsChannel pool Path MENUMain menuChannelsFavourites listsPath MENUMain menuSearchTransponder SearchSatellite search Transponder search Path MENUMain menuSearchSatellitesPath MENUMain menuSearchManual Manual input for expertsVideotext teletext Deleting a Timer Event TimerManual Timer Setting Automatic Timer SettingHinweis REc EndPath MENUMain menuSatellites SatellitesEnter/change name Enter orbit position Enter LO1 Enter LO2OFF Enable Path MENUMain menuInstallationTime offset InstallationTime offset Language/character set Signal paths TV, VCR, picture format, record, digital audioSelect character set factory setting Latin Path MENUMain menuInstallationSignal pathsAC-3 VCR signalsPicture format Digital audioPath MENUMain menuInstallationLNB LNB settingsDiSEqCTM Digital Satellite Equipment Control Xxxx Various display time, RC, LCD, download, factory resetReset Path MENUMain menuInstallationVarious Display timeDevice settings Channels in favourites list 1 general LCD display settingsTime indicator Factory resetLatin Perform factory reset on device settings00000 GermanRestore channels in favourites lists 1 Download-Over-Air Software update via satelliteOK = YES EX = no Recording Video recorder/PVR connectionPlayback Return path Muting Audio settingsSetting the volume Digital/analogue audio modeAnalogue outputs AC 3 general Backup operation Using the front panelDownload operating system Receiver to receiver data transferPreparation Channel list downloadTechnical appendix Technical featuresSoftware Update Additional featuresGeneral Sdram Type UFS 702si UFS 702swVCR/AUX AccessoriesVHS/S-VHS switching Scart socket assignmentPVR VCR Connection exampleChannel package Short technical guidePID Glossary Viterbi rate VCR connectionZapping SAT Error detection/troubleshooting and serviceProblem Cause Remedy PROSearch for new channels Channel change