Kathrein UFS 702si, UFS 702sw manual Video recorder/PVR connection, Recording, Playback

Page 51

Video recorder/PVR connection

Connect your recorder and the receiver (VCR socket) using a Scart cable. If you have a S-VHS (S-Video) recorder, from the “Installation” menu select the “Signal paths” sub-menu and change the selection (TV Scart VCR) so that the “YC” signal is output at the VCR socket.

Recording

To record a programme now running, set your recorder to record. Note that the volume on the receiver is set to full during recording (L 20 on the 7-segment display). This is the only way to obtain the full audio quality on subsequent playback. Also make sure that you do not perform any other actions on the receiver during this direct recording process – any on-screen displays would be recorded along with the programme.

For recording with the timer, refer to the “Timer” section.

Playback

	Playback via your recorder i.e. transmission of the signal
	from the VCR to the TV set, takes place automatically when
	the receiver is operating or in standby. The switching voltage
	from the recorder is detected by the receiver and the VCR
	signal is switched through to the TV set. The 7-segment
	display shows “VCR”. You can switch to the receiver
	channel at any time, even without stopping playback on
	your recorder. To do so press the ! button (green). To switch
	back to the recorder playback, press the ! button (green)
	twice.
Note:	The ! button (green) controls the TV switching voltage
	(pin 8) at the TV Scart socket. The TV switching voltage is
	activated when the video signal from the receiver or from
	the recorder is switched to the TV set. During normal
	operation, without a recorder, use the ! button (green) to
	switch between the receiver channel and an additional
	video signal to the TV set. This additional video signal to
	the TV set might, for example, come from your existing
	“analogue” antenna, from a cable connection or from a
	DVD player connected directly to the TV. The display of
	video signals available on the TV set is dependent on the
	speciﬁcation of your TV set. In the above operating mode
	with a recorder during playback, the ! button (green) would
	thus set the video sources from the TV, the recorder and
	the receiver one after the other.

51

Image 51

Contents UFS 702sw/si Important Information PrefaceContents Satellites InstallationAudio settings Error detection/troubleshooting and serviceSafety instructions important notes Receiver features Controls, displays and connections View of front panel ﬂap folded downView of rear panel LCD Display Important note on setting up receiver on a UFOmicro system Reception requirements Connecting the unitReception system presets Connection and set-upDolby connection Inserting batteries into the remote controlTV and Video recorder connection Audio connectionRemote control Remote control RC Menu concept Operating instructionsLanguage selection OSD Menu treeTV channel information Error signallingOn-Screen Displays OSD Channel informationChannel list TV/radio Channel hopping displaySwitch between TV/radio mode Channel selection using number buttons and & buttonsChannel selection Favourites list Select last channelEPG Electronic Programme Guide EPG Electronic Programme Guide Channels menu channel management Path MENUMain menuChannels Favourites list/channel arrangement move, delete, copyChannels menu channel management Channel menu channel management MoveDelete Copy Move channel block Copy channel block copy from channel pool to favourites list Delete channel blockPath MENUMain menuChannelsChannel pool Change names of favourites listsChannel pool Path MENUMain menuChannelsFavourites namesDelete one channel/all channels in channel pool Antenna signal and reception parameters button To change the PIN, activate the PIN menu item with button Parental control child lock/PINPath MENUMain menuChannelsParental control Lock To change the PIN codeMENUMain menuChannelsChannel pool Path MENUMain menuChannelsFavourites listsPath MENUMain menuSearchTransponder SearchSatellite search Transponder search Path MENUMain menuSearchSatellitesPath MENUMain menuSearchManual Manual input for expertsVideotext teletext Deleting a Timer Event TimerManual Timer Setting Automatic Timer SettingHinweis REc EndSatellites Path MENUMain menuSatellitesEnter/change name Enter LO1 Enter LO2 Enter orbit positionOFF Enable Installation Path MENUMain menuInstallationTime offsetTime offset Language/character set Signal paths TV, VCR, picture format, record, digital audioSelect character set factory setting Latin Path MENUMain menuInstallationSignal pathsAC-3 VCR signalsPicture format Digital audioPath MENUMain menuInstallationLNB LNB settingsDiSEqCTM Digital Satellite Equipment Control Xxxx Various display time, RC, LCD, download, factory resetReset Path MENUMain menuInstallationVarious Display timeDevice settings Channels in favourites list 1 general LCD display settingsTime indicator Factory resetLatin Perform factory reset on device settings00000 GermanRestore channels in favourites lists 1 Download-Over-Air Software update via satelliteOK = YES EX = no Video recorder/PVR connection RecordingPlayback Return path Muting Audio settingsSetting the volume Digital/analogue audio modeAnalogue outputs AC 3 general Backup operation Using the front panelDownload operating system Receiver to receiver data transferPreparation Channel list downloadTechnical appendix Technical featuresAdditional features Software UpdateGeneral Sdram Type UFS 702si UFS 702swVCR/AUX AccessoriesVHS/S-VHS switching Scart socket assignmentPVR VCR Connection exampleChannel package Short technical guidePID Glossary VCR connection Viterbi rateZapping SAT Error detection/troubleshooting and serviceProblem Cause Remedy PROSearch for new channels Channel change