Yamaha DVD-S795 manual Recommended setting of Digital Audio Out- put

Page 39

3 Press the cursor buttons (A, B) to select the preferred value and press SELECT.

When “1 LPCM 96k >48k” is selected

1No: Digital audio of 48 kHz/16 bit is output during playback of the DVD recorded in Linear PCM of 48 kHz. No digital audio is output during play- back of the DVD recorded in Linear PCM of 96 kHz. However, audio will be output using the original audio recording system in case of the DVD which has not been copyright-protected. (Factory preset)

2Yes: During playback of the DVD recorded in Lin- ear PCM of 48 kHz or 96 kHz, digital audio con- verted to 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)

When “2 Dolby Digital” is selected

1 Bitstream: Dolby Digital bitstream (1ch–5.1ch) is output during playback of the DVD recorded in the Dolby Digital. (Factory preset)

Select this setting when the player is connected to the Dolby Digital decoder.

2PCM\\12: Digital audio converted to PCM (2ch) of 48 kHz/16 bit is output during playback of the DVD recorded in the Dolby Digital.

When “3 dts” is selected

1Off\1: No digital audio is output during playback

of the DVD recorded in dts. (Factory preset)

2Bitstream: dts bitstream is output during playback of the DVD recorded in dts.

Select this setting when the player is connected to the dts decoder.

The screen illustrated in step 1 is displayed. Select “0” by us- ing the cursor buttons (A, B) and press SELECT to return to the initial settings screen.

Also refer to “Common procedures of initial settings” on

page 30.

Recommended setting of “Digital Audio Out- put”

Make settings as shown in table below depending on the kind of equipment that is connected to the optical/coaxial digital au- dio output connector.

 

Recommended setting

Type of equipment

 

 

 

1 LPCM

2 Dolby

 

to be connected

3 dts

96k>48k

Digital

 

 

 

 

 

 

No equipment is

No

Bitstream

Off

connected

 

 

 

 

 

 

 

AV amplifier (with

 

 

 

digital audio input

 

PCM\\12

 

connector) without

Yes\3

Off\1

Dolby Digital/dts

 

 

 

decoder

 

 

 

 

 

 

 

AV amplifier with

 

 

 

Dolby Digital decoder

Yes\3

Bitstream

Off

(See page 10.)

 

 

 

 

 

 

 

AV amplifier with

 

 

 

Dolby Digital/dts

Yes\3

Bitstream

Bitstream

decoder

 

 

 

(See page 10.)

 

 

 

 

 

 

 

ÁUnderlined item is a factory preset.

\1 When connecting an AV amplifier (with an optical/coaxial digital audio input connector) without Dolby Digital or dts decoder, be sure to select “PCM” of “2 Dolby Digital” and “Off” of “3 dts”. If “Bitstream” is selected, any attempt to play DVD may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

\2 When “PCM” is selected and “Yes” is selected for the speak- ers other than the front speakers at “8 Speaker Setting” (see page 40), only audio corresponding to the front speakers will be output from the player’s digital audio output connector during playback of the DVD recorded in Dolby Digital 5.1 ch surround. In this case, select “No” for the speakers other than the front speakers at “8 Speaker Setting”.

\3 The audio which is output from the player’s audio output connectors (6CH DISCRETE and MIXED 2CH) is also set to the Linear PCM 48 kHz sound quality level.

To enjoy high quality sound at 96 kHz, connect the amplifier or decoder directly to the audio output connectors, not to the digital audio output connector. (Select “No” at the “1 LPCM 96k>48k”.)

Initial Settings

39

Image 39
Contents DVD-S795 Risk of Electric Shock Do not Open Safety informationFCC Information for U.S.A PrecautionsAccessories Table of contents Features Definition of terms STANDBY/ON button Remote control unitControl reference guide Main unitFront panel FL display Connection Component video output connectors Y, CB, CR Video output connectorFor your reference Connection Remote control operation range B Remote control unit preparationConnecting headphones C Battery installation aBasic play Basic playStopping play Press STILL/PAUSE during play Skipping ahead or backStill picture Pause Press Skip H, I during playRapid advance Rapid reverse Slow-motion play DVD/Video CDFrame advance Frame reverse Press the cursor buttons C, D to select the preferred item Common proceduresPress on Screen during play or in the stop mode General information about On- Screen Menu IconsScreen for disc information For DVD Detailed descriptions of each On-Screen Menu IconPlayback control Audio modeScreen for disc information For Video CD/CD Track NoScreen for player information Shuttle screen To return to normal play Repeat playRepeat viewing listening Press Repeat during playRepeat of programmed track Repeating sections between two Specific points A-B repeatRepeat play To enjoy program repeat play To return to program playPress Select To return to normal play Press Play Mode in the stop modeProgram play Video CD/CD Clearing the programRandom play Video CD/CD Press Play Mode twice in the stop modeStoring markers in memory to be viewed listened to again Storing a marker in the memoryPress Audio during play Changing audio soundtrack language DVDRecalling/clearing a marker Storing markers in memory to be viewed listened to againChanging subtitle language DVD Love youJe t’aime Using a title menu DVD Using a DVD menu DVDViewing from another angle DVD To cancel during setup operation Initial settingsCommon procedures of initial settings Press SET UP in the stop modeSelecting disc languages DVD Selecting rating level DVD When level 7 or lower is selectedSelecting language of On-Screen Display menu When the player is lockedOn-Screen Messages When 1 On-Screen Messages is selectedWhen 2 Color and Position is selected Selecting the display format On-Screen DisplayDim During DVD/VCD Play Auto Selecting the FL display brightnessBright DimSelecting TV screen type Pan & Scan style Software Pan & ScanStyle FormattedDts Selecting digital outputLpcm 96k48k Dolby DigitalRecommended setting of Digital Audio Out- put Speaker settings Delay time Speaker Delay time Difference between D1 D2/D3To adjust the channel balance using the test signal Other settings When 5 Still Picture Display is selected When 2 Audio during Search is selectedWhen 3 TV Mode 43 is selected When 4 D. Dynamic Range Compression is selectedLanguage code list Maintenance Disc handling and maintenanceSymptom Common Remedy TroubleshootingSelf-diagnosis display function Specifications