Avaya S8400 manual Enabling firewall settings, Click Execute Ping

Page 40

Chapter 4: Media server configuration

Verifying media server connection to the customer’s LAN (if provided)

1.Under Diagnostics, click Ping.

2.Select Host Name Or IP Address and type in the IP address of a computer on the network.

3.Click Execute Ping.

4.Verify that the ping was successful, indicating that the media server is connected to the customer’s network.

5.If DNS is administered, type in the host name of a computer on the network.

6.Click Execute Ping.

7.Verify that the ping was successful, indicating that DNS is working.

If possible, have a customer representative do the following test from a computer on the network:

1.Click Start > Run to open the Run dialog box.

2.Type command and click OK to open an MS-DOS command window.

3.Type ping serveripaddress and click OK, where serveripaddress is the IP address of the media server.

4.Verify that the ping was successful.

5.If DNS is administered, type ping servername and press Enter, where servername is the host name of the media server.

6.Verify that the ping was successful.

Enabling firewall settings

For the media server to receive SNMP traps from the UPS and Avaya Ethernet switch, you must enable the snmptrap, 162/udp port. The default is disabled.

1.Under Security, click Firewall.

2.Click Advanced Settings . . . to view the second page.

3.Scroll down until you see snmptrap, port 162/udp.

4.Select the box in the Input to Server column (far left) next to it.

40 Installing and Configuring the Avaya S8400 Media Server

February 2006

Image 40
Contents Installing and Configuring the Avaya S8400 Media Server ReleaseAvaya Inc All Rights Reserved Contents Contents Contents Contents Introduction AudienceHow to use this documentation Documentation Pre-installation before going on siteVerifying site readiness Laptop preparation, software, and system information Copying files to the laptopAbout ASG and the unique on-site password Obtaining license and Avaya authentication filesIntroduction Pre-installation at the site Equipment specificationsAbout media server port connections TN8400AP features and specifications1Ethernet ports Media server cable adapter Media server cable adapterEthernet connectivity with the TN8412AP circuit pack Media server cable adapter port labelingPort Name FunctionIPSI-2 cable adapter Figure notes Services access port About Modem connections About Media GatewaysAbout Processor Ethernet About SSH TN8412AP SipiHigh level overview of installation process Installing and cabling the media gatewaysInstalling Avaya Communication Manager Configuring the MPCTesting the finished installation Completing the installation administrationTranslating the Sipi Snmp Configuration Configuration of the Snmp modules in the UPSDefault UPS IP addresses Preparing to configure the Snmp moduleAdministering the Snmp module Security AlertSetting selected traps alarming Communication Manager Installation Clearing the ARP cache on the laptopPowering up the media server Connecting the CD/DVD drive to the media serverAccessing the media server Configuring Telnet for Windows 2000/XP Close the dialog boxInstalling Avaya Communication Manager Installing IA 770 Intuity Audix Messaging Page Opening the Maintenance Web Interface Media server configurationWhen asked Do you want to suppress alarms?, select Yes Click Launch Maintenance Web Interface Copying files to the media serverEnabling Network Time Servers Using the Installation Wizard Click Launch Avaya Installation WizardInstalling MPC firmware Enter sampcmd samp-update statusVerifying MPC IP information IP Address field Subnet Mask fieldEnabling firewall settings Click Execute PingConfiguring the modem Left menu click Set Modem InterfaceSelect the Change Modem Setting and click Continue Click Close WindowIP interface translations Inputting initial system translations Starting SAT terminal emulationAdding media gateways Enabling Sipi Cabinet Cabinet DescriptionAdding the Sipi to the system Set the Ipsi Control of Port Networks field to enabledType add ipserver-interface PNnumber and press Enter Type change system-parameters maintenance and press Enter Setting alarm activation levelSaving translations Page IP interface configuration Sipi address configurationConnecting the laptop directly to the Sipi Programming the Sipi for static addressingSipi address configuration Setting the Vlan and diffserv parameters Enter show control interfaceResetting the Sipi Sipi LED display for static addressVerifying connectivity to media server Verifying that Sipi is translatedUpgrading the Sipi firmware version if necessary Type list ipserver-interface and press EnterEnabling control of Sipi Verifying license statusPage Verifying translations Post-installation administrationList station List trunk-group List hunt-group Setting daylight savings time rules Type change daylight-savings-rules and press EnterSetting locations if necessary Type change locations and press EnterVerifying date and time Clearing and resolving alarmsUnder Server, click Set Server Time/Timezone Enabling alarms to Inads via modem Backing up files to the compact flash mediaEnabling alarms to Inads via Snmp Before leaving the siteInstallation verification Testing the Sipi circuit pack Testing the license fileTN8400AP Media Server LEDs TN8400AP Media Server faceplateFaceplate interfaces LED descriptions Avaya S8400 Media Server LED descriptionsLEDs on Powerware 9125 UPS UPS LEDsTN8412AP Sipi LEDs TN8412AP Sipi circuit pack faceplate graphic shows Ipsi 030502KLC Ledlip1 Page Appendix a Media server access Accessing the server’s command line interface with SSHAppendix a Media server access Connecting to the media server directly Connecting to the media server remotely over the network Connecting to the media server remotely over a modem Accessing the Maintenance Web Interface Using the SAT command line promptLogins for Avaya technicians and Business Partners Configuring the network for Windows 2000/XP Select Internet Protocol TCP/IPSubnet mask Select Use the following DNS server addressesSetting browser options for Internet Explorer Click on LAN settings, then AdvancedPage Appendix B Installation troubleshooting Troubleshooting media server hardware installationTroubleshooting media server hardware installation Problem Possible solutionTroubleshooting configuring the media server hardware Ping 192.11.13.6 and type EnterMS-DOS command window, type arp -d 192.11.13.6 Appendix B Installation troubleshooting Index Directly Remotely over modem Remotely over networkMedia gateways, adding