SUPER MICRO Computer 6015T-INF, 6015T-T manual Creating a RAID 10 RAID 1+ RAID

Page 106

SUPERSERVER 6015T-T/6015T-INF User's Manual

Creating a RAID 10 (RAID 1+ RAID 0)

a. Select "Create RAID Volume" from the main menu and press the <Enter> key. The following screen will appear:

b. Specify a name for the RAID 10 set and press <Enter>.

c. When RAID Level item is highlighted, use the <Up Arrow>, <Down Arrow> keys to select RAID 10 (RAID1 + RAID0) and hit <Enter>.

d. When the Stripe Size is highlighted, use the <Up Arrow>, <Down Arrow> keys to select the stripe size from 4 KB to 128 KB for your RAID 10 and hit <Enter>. The default setting is 64 KB. (Note: For a server, please use a lower stripe size, and for a multimedia system, use a higher stripe size.)

e. When the RAID Volume Capacity item is highlighted, enter your RAID volume capacity and hit <Enter>. The default setting is the maximum capacity allowed.

f. Press <Enter> when the Create Volume item is highlighted. A warning message displays.

g. When asked "Are you sure you want to create this volume (Y/N), press "Y" to create the RAID volume, or type "N" to go back to the Create Volume menu.

C-6

Image 106

Contents Super Manual Revision 1.0b Release Date April 7 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendices Page Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesATI Graphics Controller ESB2 Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesEurope Contacting SupermicroHeadquarters Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a Telco RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Check the Sata drives Checking the Drive Bay SetupSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Check compatibility of serverboard ports and I/O shield Serverboard InstallationUnpacking Mounting the serverboard onto the serverboard trayConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkInstalling memory modules Installing MemoryMemory support Adding PCI Cards PCI card installationBit PCI-X slot Serverboard Details X7DBT-T/X7DBT-INF Layout Not drawn to scaleLED Indicator Description Jumper Description Default SettingConnector Description X7DBT-T/X7DBT-INF Quick ReferenceAuxiliary Power Connector Connector DeﬁnitionsATX Power Connector Pwon ConnectorOverheat LED OH NIC2 LAN2 LEDFan Headers Power On LEDNMI Button Chassis IntrusionLAN1/2 Ethernet Ports Universal Serial Bus USBWake-On-LAN Serial Ports Wake-On-RingSgpio Header SMB Power I2C SMBExplanation Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearWatch Dog Enable/Disable LAN1/LAN2 Enable/DisableI2C to PCI-Express Slot InﬁniBand LED Indicators LE2/ LE3 Onboard IndicatorsOnboard Power LED LE1 LAN1/LAN2 LEDsStatic-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front ViewSata Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays System FansRemoving a Sata Drive Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving the Power Supply Starting the Setup Utility System BiosHow To Change the Conﬁguration Data ChapterMain Bios Setup Running SetupPress the Delete key to enter Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System DateType LBA Mode ControlMulti-Sector Transfers Native Mode Operation Transfer ModeUltra DMA Mode Sata Controller ModeSystem Memory Sata Ahci Available when Sata RAID is DisabledExtended Memory QuickBoot Mode Advanced SetupBoot Features QuietBoot ModePower Loss Control Acpi ModePower Button Behavior Memory Cache Cache System Bios AreaCache Extended Memory Cache Base 0-512KCache Base 512K-640K Discrete Mtrr AllocationPCI Parity Error Forwarding Default Primary Video AdapterEmulated IRQ Solutions Reset Conﬁguration DataLarge Disk Access Mode Enable MasterLatency Timer Serr Signal ConditionBranch 0/1 Rank Interleaving Memory Branch ModeHigh Temperature Dram Operation Branch 0/1 Rank SparingEnabling Multi-Media Timer Crystal Beach FeaturesClock Spectrum Feature Snoop FilterAdvanced Processor Options CPU SpeedDCA Delay Clocks Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU Intel Eist Support Available when supported by the CPUMode Device ConﬁgurationSerial Port B Base I/O AddressBaud Rate Console RedirectionCOM Port Address Console TypeVoltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring Existing Event Log Number System Event LoggingClear System Event Logging Event Log ControlTimer for Loading OS Minutes System Event Log/System Event Log List ModeOS Boot Watch Dog Time Out OptionRealtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupDevice IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM PassedSystem Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Important Notes to the User Intel HostRAID Setup GuidelinesIntroduction to Serial ATA and Parallel ATA Serial ATA SataIntel HostRAID Conﬁgurations Intel Matrix StorageUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations Chassis WeightPower Supply System CoolingRegulatory Compliance