SUPER MICRO Computer 6015T-T, 6015T-INF Adding PCI Cards, Bit PCI-X slot, PCI card installation

Page 45

Chapter 5: Advanced Serverboard Setup

5-7 Adding PCI Cards

1. 64-bit PCI-X slot

The 6015T-T/6015T-INF includes two preinstalled riser cards designed speciﬁ cally for use in the SC808T-980 1U rackmount chassis. These riser cards support two low-proﬁ le PCI-Express x8 cards to ﬁ t inside the chassis.

2. PCI card installation

The riser card has already been preinstalled into the serverboard. Perform the following steps to add a PCI add-on card:

1.Remove the PCI slot shield on the chassis by releasing the locking tab.

2.Insert the add-on card into the riser card.

3.Secure the add-on card with the locking tab.

5-9

Image 45

Contents Super Manual Revision 1.0b Release Date April 7 Preface About This ManualManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Page Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsOther Features Onboard Controllers/PortsATI Graphics Controller ESB2 Server Chassis Features Sata Backplane/Drives 1U Twin System NotesHeadquarters Contacting SupermicroEurope Asia-PaciﬁcPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Installing the Inner RailsIdentifying the Sections of the Rack Rails Locking Tabs Installing the Outer RailsInstalling the Server into a Telco Rack Installing the Server into the RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Supplying power to the system Checking the Drive Bay SetupCheck the Sata drives Check the airﬂowControl Panel Buttons Chapter System InterfaceControl Panel LEDs Sata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Serverboard InstallationCheck compatibility of serverboard ports and I/O shield Mounting the serverboard onto the serverboard trayConnecting Cables Connecting Data CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkInstalling Memory Installing memory modulesMemory support PCI card installation Adding PCI CardsBit PCI-X slot X7DBT-T/X7DBT-INF Layout Not drawn to scale Serverboard DetailsConnector Description Jumper Description Default SettingLED Indicator Description X7DBT-T/X7DBT-INF Quick ReferenceATX Power Connector Connector DeﬁnitionsAuxiliary Power Connector Pwon ConnectorNIC2 LAN2 LED Overheat LED OHNMI Button Power On LEDFan Headers Chassis IntrusionUniversal Serial Bus USB LAN1/2 Ethernet PortsWake-On-LAN Wake-On-Ring Serial PortsSgpio Header SMB SMB Power I2CVGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearLAN1/LAN2 Enable/Disable Watch Dog Enable/DisableI2C to PCI-Express Slot Onboard Power LED LE1 Onboard IndicatorsInﬁniBand LED Indicators LE2/ LE3 LAN1/LAN2 LEDsChapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSata Drive Installation System FansRemoving a Sata Drive Power Supply Failure Power SupplyReplacing the Power Supply Removing the power supplyRemoving the Power Supply How To Change the Conﬁguration Data System BiosStarting the Setup Utility ChapterRunning Setup Main Bios SetupPress the Delete key to enter Setup Bios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateLBA Mode Control TypeMulti-Sector Transfers Ultra DMA Mode Transfer ModeNative Mode Operation Sata Controller ModeSata Ahci Available when Sata RAID is Disabled System MemoryExtended Memory Boot Features Advanced SetupQuickBoot Mode QuietBoot ModePower Button Behavior Acpi ModePower Loss Control Memory Cache Cache System Bios AreaCache Base 512K-640K Cache Base 0-512KCache Extended Memory Discrete Mtrr AllocationEmulated IRQ Solutions Default Primary Video AdapterPCI Parity Error Forwarding Reset Conﬁguration DataLatency Timer Enable MasterLarge Disk Access Mode Serr Signal ConditionHigh Temperature Dram Operation Memory Branch ModeBranch 0/1 Rank Interleaving Branch 0/1 Rank SparingClock Spectrum Feature Crystal Beach FeaturesEnabling Multi-Media Timer Snoop FilterCPU Speed Advanced Processor OptionsDirect Cache Access Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDCA Delay Clocks Available when supported by the CPU Intel Eist Support Available when supported by the CPUSerial Port B Device ConﬁgurationMode Base I/O AddressCOM Port Address Console RedirectionBaud Rate Console TypeHardware Monitor Logic CPU Temperature ThresholdVoltage Monitoring Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring Clear System Event Logging System Event LoggingExisting Event Log Number Event Log ControlOS Boot Watch Dog System Event Log/System Event Log List ModeTimer for Loading OS Minutes Time Out OptionRealtime Sensor Data User Password Is Supervisor Password IsSet Supervisor Password Set User PasswordBoot Password on BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupInvalid System Conﬁguration Data PS/2 Mouse Boot Summary ScreenDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Introduction to Serial ATA and Parallel ATA Intel HostRAID Setup GuidelinesImportant Notes to the User Serial ATA SataIntel Matrix Storage Intel HostRAID ConﬁgurationsUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Exiting the Intel Matrix Storage Manager Utility Resetting to Non-RAID and Resetting a RAID HDDInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations Power Supply WeightChassis System CoolingRegulatory Compliance