SUPER MICRO Computer 6015T-T manual Console Redirection, COM Port Address, Baud Rate, Console Type

Page 79

Chapter 7: BIOS

Console Redirection

Access the submenu to make changes to the following settings.

COM Port Address

This item allows you to specify which COM port to direct the remote console to: Onboard COM A or Onboard COM B. This setting can also be Disabled.

BAUD Rate

This item allows you to set the BAUD rate for console redirection. The options are 300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, and 115.2K.

Console Type

This item allows you to set console redirection type. The options are VT100, VT100,8bit, PC-ANSI, 7bit, PC ANSI, VT100+, VT-UTF8 and ASCII.

Flow Control

This item allows you to select the ﬂ ow control option for console redirection. The options are None, XON/XOFF and CTS/RTS.

Console Connection

This item allows you to decide how console redirection is to be connected: either Direct or Via Modem.

Continue CR after POST

Choose whether to continue with console redirection after the POST routine. The options are On and Off.

7-17

Image 79

Contents Super Manual Revision 1.0b Release Date April 7 About This Manual PrefaceManual Organization Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Page Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesATI Graphics Controller ESB2 Server Chassis Features Sata Backplane/Drives 1U Twin System NotesAsia-Paciﬁc Contacting SupermicroHeadquarters EuropePage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Locking Tabs Installing the Outer RailsInstalling the Server into a Telco Rack Installing the Server into the RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Check the airﬂow Checking the Drive Bay SetupSupplying power to the system Check the Sata drivesControl Panel Buttons Chapter System InterfaceControl Panel LEDs Sata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Mounting the serverboard onto the serverboard tray Serverboard InstallationUnpacking Check compatibility of serverboard ports and I/O shieldConnecting Data Cables Connecting CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkInstalling memory modules Installing MemoryMemory support Adding PCI Cards PCI card installationBit PCI-X slot X7DBT-T/X7DBT-INF Layout Not drawn to scale Serverboard DetailsX7DBT-T/X7DBT-INF Quick Reference Jumper Description Default SettingConnector Description LED Indicator DescriptionPwon Connector Connector DeﬁnitionsATX Power Connector Auxiliary Power ConnectorNIC2 LAN2 LED Overheat LED OHChassis Intrusion Power On LEDNMI Button Fan HeadersLAN1/2 Ethernet Ports Universal Serial Bus USBWake-On-LAN Serial Ports Wake-On-RingSgpio Header SMB SMB Power I2CCmos Clear Jumper SettingsVGA Enable/Disable Explanation JumpersWatch Dog Enable/Disable LAN1/LAN2 Enable/DisableI2C to PCI-Express Slot LAN1/LAN2 LEDs Onboard IndicatorsOnboard Power LED LE1 InﬁniBand LED Indicators LE2/ LE3Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Chassis Front View Control PanelSystem Fans Drive Bay Installation/RemovalAccessing the Drive Bays Sata Drive InstallationRemoving a Sata Drive Removing the power supply Power SupplyPower Supply Failure Replacing the Power SupplyRemoving the Power Supply Chapter System BiosHow To Change the Conﬁguration Data Starting the Setup UtilityMain Bios Setup Running SetupPress the Delete key to enter Setup System Date Main Bios Setup Menu Main Setup FeaturesBios Date System TimeType LBA Mode ControlMulti-Sector Transfers Sata Controller Mode Transfer ModeUltra DMA Mode Native Mode OperationSystem Memory Sata Ahci Available when Sata RAID is DisabledExtended Memory QuietBoot Mode Advanced SetupBoot Features QuickBoot ModeMemory Cache Cache System Bios Area Acpi ModePower Button Behavior Power Loss ControlDiscrete Mtrr Allocation Cache Base 0-512KCache Base 512K-640K Cache Extended MemoryReset Conﬁguration Data Default Primary Video AdapterEmulated IRQ Solutions PCI Parity Error ForwardingSerr Signal Condition Enable MasterLatency Timer Large Disk Access ModeBranch 0/1 Rank Sparing Memory Branch ModeHigh Temperature Dram Operation Branch 0/1 Rank InterleavingSnoop Filter Crystal Beach FeaturesClock Spectrum Feature Enabling Multi-Media TimerCPU Speed Advanced Processor OptionsIntel Eist Support Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU DCA Delay Clocks Available when supported by the CPUBase I/O Address Device ConﬁgurationSerial Port B ModeConsole Type Console RedirectionCOM Port Address Baud RateFan Speed Control Modes CPU Temperature ThresholdHardware Monitor Logic Voltage MonitoringCPU Temperature Threshold See note on Temperature Monitoring Event Log Control System Event LoggingClear System Event Logging Existing Event Log NumberTime Out Option System Event Log/System Event Log List ModeOS Boot Watch Dog Timer for Loading OS MinutesRealtime Sensor Data Set User Password Supervisor Password IsUser Password Is Set Supervisor PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Check date and time settings System Cmos checksum bad Default conﬁguration usedSystem timer error Real time clock errorEntering Setup System cache error Cache disabledFail-Safe Timer NMI Failed Allocation Error for deviceNnnn kB Extended RAM Passed PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂictVideo Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedPage Post Code Description Appendix B Bios Post CodesRecoverable Post Errors Terminal Post ErrorsPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Serial ATA Sata Intel HostRAID Setup GuidelinesIntroduction to Serial ATA and Parallel ATA Important Notes to the UserIntel Matrix Storage Intel HostRAID ConﬁgurationsUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Exiting the Intel Matrix Storage Manager Utility Resetting to Non-RAID and Resetting a RAID HDDInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations System Cooling WeightPower Supply ChassisRegulatory Compliance