SUPER MICRO Computer 6015T-T, 6015T-INF manual Preface

Page 5

Preface

Notes

v

Image 5
Contents Super Manual Revision 1.0b Release Date April 7 Manual Organization PrefaceAbout This Manual Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Page Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsATI Graphics Controller Other FeaturesOnboard Controllers/Ports ESB2 Server Chassis Features Sata Backplane/Drives 1U Twin System NotesHeadquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Locking Tabs Installing the Outer RailsInstalling the Server into a Telco Rack Installing the Server into the RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Supplying power to the system Checking the Drive Bay SetupCheck the Sata drives Check the airflowControl Panel Buttons Chapter System InterfaceControl Panel LEDs Sata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions Unpacking Serverboard InstallationCheck compatibility of serverboard ports and I/O shield Mounting the serverboard onto the serverboard trayConnecting Power Cables Connecting CablesConnecting Data Cables I/O Ports Connecting the Control PanelInstalling the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the HeatsinkMemory support Installing MemoryInstalling memory modules Bit PCI-X slot PCI card installationAdding PCI Cards X7DBT-T/X7DBT-INF Layout Not drawn to scale Serverboard DetailsConnector Description Jumper Description Default SettingLED Indicator Description X7DBT-T/X7DBT-INF Quick ReferenceATX Power Connector Connector DefinitionsAuxiliary Power Connector Pwon ConnectorNIC2 LAN2 LED Overheat LED OHNMI Button Power On LEDFan Headers Chassis IntrusionWake-On-LAN Universal Serial Bus USBLAN1/2 Ethernet Ports Sgpio Header Wake-On-RingSerial Ports SMB SMB Power I2CVGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearI2C to PCI-Express Slot LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable Onboard Power LED LE1 Onboard IndicatorsInfiniBand LED Indicators LE2/ LE3 LAN1/LAN2 LEDsTools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Chassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSata Drive Installation System FansRemoving a Sata Drive Power Supply Failure Power SupplyReplacing the Power Supply Removing the power supplyRemoving the Power Supply How To Change the Configuration Data System BiosStarting the Setup Utility ChapterPress the Delete key to enter Setup Running SetupMain Bios Setup Bios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateMulti-Sector Transfers LBA Mode ControlType Ultra DMA Mode Transfer ModeNative Mode Operation Sata Controller ModeExtended Memory Sata Ahci Available when Sata RAID is DisabledSystem Memory Boot Features Advanced SetupQuickBoot Mode QuietBoot ModePower Button Behavior Acpi ModePower Loss Control Memory Cache Cache System Bios AreaCache Base 512K-640K Cache Base 0-512KCache Extended Memory Discrete Mtrr AllocationEmulated IRQ Solutions Default Primary Video AdapterPCI Parity Error Forwarding Reset Configuration DataLatency Timer Enable MasterLarge Disk Access Mode Serr Signal ConditionHigh Temperature Dram Operation Memory Branch ModeBranch 0/1 Rank Interleaving Branch 0/1 Rank SparingClock Spectrum Feature Crystal Beach FeaturesEnabling Multi-Media Timer Snoop FilterCPU Speed Advanced Processor OptionsDirect Cache Access Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDCA Delay Clocks Available when supported by the CPU Intel Eist Support Available when supported by the CPUSerial Port B Device ConfigurationMode Base I/O AddressCOM Port Address Console RedirectionBaud Rate Console TypeHardware Monitor Logic CPU Temperature ThresholdVoltage Monitoring Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring Clear System Event Logging System Event LoggingExisting Event Log Number Event Log ControlOS Boot Watch Dog System Event Log/System Event Log List ModeTimer for Loading OS Minutes Time Out OptionRealtime Sensor Data User Password Is Supervisor Password IsSet Supervisor Password Set User PasswordBoot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages System timer error System Cmos checksum bad Default configuration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupInvalid System Configuration Data PS/2 Mouse Boot Summary ScreenDevice IRQ conflict Nnnn kB Extended RAM PassedPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Introduction to Serial ATA and Parallel ATA Intel HostRAID Setup GuidelinesImportant Notes to the User Serial ATA SataIntel Matrix Storage Intel HostRAID ConfigurationsUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Exiting the Intel Matrix Storage Manager Utility Resetting to Non-RAID and Resetting a RAID HDDInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Specifications Power Supply WeightChassis System CoolingRegulatory Compliance