SUPER MICRO Computer 6015T-INF, 6015T-T manual Checking the Drive Bay Setup, Check the Sata drives

Page 28

SUPERSERVER 6015T-T/6015T-INF User's Manual

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SATA drives and SATA backplane have been properly installed and all connections have been made.

1.Check the SATA drives

Depending upon your system's conﬁ guration, your system may have one or more drives already installed. If you need to install SATA drives, please refer to Chapter 6.

2.Check the airﬂow

Airﬂ ow is provided by six sets of 4-cm fans (each set of fans consists of two fans that are mounted back to back). The system component layout was carefully designed to direct sufﬁ cient cooling airﬂ ow to the components that generate the most heat. Note that all power and data cables have been routed in such a way that they do not block the airﬂ ow generated by the fans.

3.Supplying power to the system

The last thing you must do is to provide input power to the system. Plug the power cord from the power supply module into a high-quality power strip that offers protection from electrical noise and power surges. It is recommended that you use an uninterruptible power supply (UPS) source.

2-10

Image 28

Contents Super Manual Revision 1.0b Release Date April 7 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendices Page Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesATI Graphics Controller ESB2 Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesContacting Supermicro HeadquartersEurope Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a Telco RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Supplying power to the systemCheck the Sata drives Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Serverboard Installation UnpackingCheck compatibility of serverboard ports and I/O shield Mounting the serverboard onto the serverboard trayConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkInstalling memory modules Installing MemoryMemory support Adding PCI Cards PCI card installationBit PCI-X slot Serverboard Details X7DBT-T/X7DBT-INF Layout Not drawn to scaleJumper Description Default Setting Connector DescriptionLED Indicator Description X7DBT-T/X7DBT-INF Quick ReferenceConnector Deﬁnitions ATX Power ConnectorAuxiliary Power Connector Pwon ConnectorOverheat LED OH NIC2 LAN2 LEDPower On LED NMI ButtonFan Headers Chassis IntrusionLAN1/2 Ethernet Ports Universal Serial Bus USBWake-On-LAN Serial Ports Wake-On-RingSgpio Header SMB Power I2C SMBJumper Settings VGA Enable/DisableExplanation Jumpers Cmos ClearWatch Dog Enable/Disable LAN1/LAN2 Enable/DisableI2C to PCI-Express Slot Onboard Indicators Onboard Power LED LE1InﬁniBand LED Indicators LE2/ LE3 LAN1/LAN2 LEDsStatic-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front ViewDrive Bay Installation/Removal Accessing the Drive BaysSata Drive Installation System FansRemoving a Sata Drive Power Supply Power Supply FailureReplacing the Power Supply Removing the power supplyRemoving the Power Supply System Bios How To Change the Conﬁguration DataStarting the Setup Utility ChapterMain Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup Features Bios DateSystem Time System DateType LBA Mode ControlMulti-Sector Transfers Transfer Mode Ultra DMA ModeNative Mode Operation Sata Controller ModeSystem Memory Sata Ahci Available when Sata RAID is DisabledExtended Memory Advanced Setup Boot FeaturesQuickBoot Mode QuietBoot ModeAcpi Mode Power Button BehaviorPower Loss Control Memory Cache Cache System Bios AreaCache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationDefault Primary Video Adapter Emulated IRQ SolutionsPCI Parity Error Forwarding Reset Conﬁguration DataEnable Master Latency TimerLarge Disk Access Mode Serr Signal ConditionMemory Branch Mode High Temperature Dram OperationBranch 0/1 Rank Interleaving Branch 0/1 Rank SparingCrystal Beach Features Clock Spectrum FeatureEnabling Multi-Media Timer Snoop FilterAdvanced Processor Options CPU SpeedHardware Prefetch Available when supported by the CPU Direct Cache Access Available when supported by the CPUDCA Delay Clocks Available when supported by the CPU Intel Eist Support Available when supported by the CPUDevice Conﬁguration Serial Port BMode Base I/O AddressConsole Redirection COM Port AddressBaud Rate Console TypeCPU Temperature Threshold Hardware Monitor LogicVoltage Monitoring Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring System Event Logging Clear System Event LoggingExisting Event Log Number Event Log ControlSystem Event Log/System Event Log List Mode OS Boot Watch DogTimer for Loading OS Minutes Time Out OptionRealtime Sensor Data Supervisor Password Is User Password IsSet Supervisor Password Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsSystem cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering SetupPS/2 Mouse Boot Summary Screen Invalid System Conﬁguration DataDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Intel HostRAID Setup Guidelines Introduction to Serial ATA and Parallel ATAImportant Notes to the User Serial ATA SataIntel HostRAID Conﬁgurations Intel Matrix StorageUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations Weight Power SupplyChassis System CoolingRegulatory Compliance