SUPER MICRO Computer 6015T-INF, 6015T-T manual

Page 42

SUPERSERVER 6015T-T/6015T-INF User's Manual

3.Use your thumb and your index fi nger to hold the CPU at opposite sides.

4.Align pin1 of the CPU (the cor- ner marked with a triangle) with the notched corner of the CPU socket.

5.Find the corner of the CPU that has a semi-circle cutout below a gold dot (CPU key). This corner should be aligned with the cutout on the socket (socket key).

6.Once aligned, carefully lower the CPU straight down into the socket. Do not drop the CPU on the socket, do not move the CPU horizontally or vertically and do not rub the CPU against any surface or any of the contacts, which may damage the CPU and/or contacts.

7.With the CPU in the socket, inspect the four corners of the CPU to make sure that it is properly installed.

8.Use your thumb to gently push the load lever down until it snaps into the retention clasp.

9.If the CPU is properly installed into the socket, the PnP cap will be auto- matically released from the load plate when the lever locks. Remove the cap. Repeat steps to install a second CPU if desired.

Warning! Keep the plastic PnP cap. The serverboard must be shipped with the PnP cap properly installed to protect the CPU socket. Shipment without the PnP cap properly installed will void the warranty.

Gold dot

Socket key

CPU key

Notched corner

CPU pin 1

Load lever

CPU installed in socket

PnP cap released

from load plate

5-6

Image 42
Contents Super Manual Revision 1.0b Release Date April 7 Preface About This ManualManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendices Page Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsOther Features Onboard Controllers/PortsATI Graphics Controller ESB2 Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesEurope Contacting SupermicroHeadquarters Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Installing the Inner RailsIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a Telco RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Check the Sata drives Checking the Drive Bay SetupSupplying power to the system Check the airflowChapter System Interface Control Panel ButtonsControl Panel LEDs Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Check compatibility of serverboard ports and I/O shield Serverboard InstallationUnpacking Mounting the serverboard onto the serverboard trayConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkInstalling Memory Installing memory modulesMemory support PCI card installation Adding PCI CardsBit PCI-X slot Serverboard Details X7DBT-T/X7DBT-INF Layout Not drawn to scaleLED Indicator Description Jumper Description Default SettingConnector Description X7DBT-T/X7DBT-INF Quick ReferenceAuxiliary Power Connector Connector DefinitionsATX Power Connector Pwon ConnectorOverheat LED OH NIC2 LAN2 LEDFan Headers Power On LEDNMI Button Chassis IntrusionUniversal Serial Bus USB LAN1/2 Ethernet PortsWake-On-LAN Wake-On-Ring Serial PortsSgpio Header SMB Power I2C SMBExplanation Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearLAN1/LAN2 Enable/Disable Watch Dog Enable/DisableI2C to PCI-Express Slot InfiniBand LED Indicators LE2/ LE3 Onboard IndicatorsOnboard Power LED LE1 LAN1/LAN2 LEDsChapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front ViewSata Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays System FansRemoving a Sata Drive Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving the Power Supply Starting the Setup Utility System BiosHow To Change the Configuration Data ChapterRunning Setup Main Bios SetupPress the Delete key to enter Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System DateLBA Mode Control TypeMulti-Sector Transfers Native Mode Operation Transfer ModeUltra DMA Mode Sata Controller ModeSata Ahci Available when Sata RAID is Disabled System MemoryExtended Memory QuickBoot Mode Advanced SetupBoot Features QuietBoot ModePower Loss Control Acpi ModePower Button Behavior Memory Cache Cache System Bios AreaCache Extended Memory Cache Base 0-512KCache Base 512K-640K Discrete Mtrr AllocationPCI Parity Error Forwarding Default Primary Video AdapterEmulated IRQ Solutions Reset Configuration DataLarge Disk Access Mode Enable MasterLatency Timer Serr Signal ConditionBranch 0/1 Rank Interleaving Memory Branch ModeHigh Temperature Dram Operation Branch 0/1 Rank SparingEnabling Multi-Media Timer Crystal Beach FeaturesClock Spectrum Feature Snoop FilterAdvanced Processor Options CPU SpeedDCA Delay Clocks Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU Intel Eist Support Available when supported by the CPUMode Device ConfigurationSerial Port B Base I/O AddressBaud Rate Console RedirectionCOM Port Address Console TypeVoltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring Existing Event Log Number System Event LoggingClear System Event Logging Event Log ControlTimer for Loading OS Minutes System Event Log/System Event Log List ModeOS Boot Watch Dog Time Out OptionRealtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User PasswordBoot Password on BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupDevice IRQ conflict PS/2 Mouse Boot Summary ScreenInvalid System Configuration Data Nnnn kB Extended RAM PassedSystem Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Important Notes to the User Intel HostRAID Setup GuidelinesIntroduction to Serial ATA and Parallel ATA Serial ATA SataIntel HostRAID Configurations Intel Matrix StorageUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Specifications Chassis WeightPower Supply System CoolingRegulatory Compliance