SUPER MICRO Computer 6015T-INF manual Device Conﬁguration, Serial Port B, Mode, Base I/O Address

Page 78

SUPERSERVER 6015T-T/6015T-INF User's Manual

I/O Device Conﬁguration

Access the submenu to make changes to the following settings.

Serial Port B

This setting allows you to assign control of serial port B. The options are Enabled (user deﬁ ned), Disabled, Auto (BIOS controlled) and OS Controlled.

Mode

This setting allows you to set the type of device that will be connected to serial port B. The options are Normal, IR (for an infrared device) and ASK_IR.

Base I/O Address

This setting allows you to select the base I/O address for serial port B. The options are 3F8, 2F8, 3E8 and 2E8.

Interrupt

This setting allows you to select the IRQ (interrupt request) for serial port B. The options are IRQ3 and IRQ4.

DMI Event Logging

Access the submenu to make changes to the following settings.

Event Log Validity

This is a display to inform you of the event log validity. It is not a setting.

Event Log Capacity

This is a display to inform you of the event log capacity. It is not a setting.

View DMI Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Event Logging

This setting allows you to Enable or Disable event logging.

ECC Event Logging

This setting allows you to Enable or Disable ECC event logging.

Mark DMI Events as Read

Highlight this item and press <Enter> to mark the DMI events as read.

Clear All DMI Event Logs

Select Yes and press <Enter> to clear all DMI event logs. The options are Yes and No.

7-16

Image 78

Contents Super Manual Revision 1.0b Release Date April 7 Preface About This ManualManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendices Page Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsOther Features Onboard Controllers/PortsATI Graphics Controller ESB2 Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesEurope Contacting SupermicroHeadquarters Asia-PaciﬁcPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Installing the Inner RailsIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking TabsInstalling the Server into the Rack Installing the Server into a Telco RackInstalling the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Check the Sata drives Checking the Drive Bay SetupSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Check compatibility of serverboard ports and I/O shield Serverboard InstallationUnpacking Mounting the serverboard onto the serverboard trayConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the HeatsinkInstalling Memory Installing memory modulesMemory support PCI card installation Adding PCI CardsBit PCI-X slot Serverboard Details X7DBT-T/X7DBT-INF Layout Not drawn to scaleLED Indicator Description Jumper Description Default SettingConnector Description X7DBT-T/X7DBT-INF Quick ReferenceAuxiliary Power Connector Connector DeﬁnitionsATX Power Connector Pwon ConnectorOverheat LED OH NIC2 LAN2 LEDFan Headers Power On LEDNMI Button Chassis IntrusionUniversal Serial Bus USB LAN1/2 Ethernet PortsWake-On-LAN Wake-On-Ring Serial PortsSgpio Header SMB Power I2C SMBExplanation Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearLAN1/LAN2 Enable/Disable Watch Dog Enable/DisableI2C to PCI-Express Slot InﬁniBand LED Indicators LE2/ LE3 Onboard IndicatorsOnboard Power LED LE1 LAN1/LAN2 LEDsChapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front ViewSata Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays System FansRemoving a Sata Drive Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving the Power Supply Starting the Setup Utility System BiosHow To Change the Conﬁguration Data ChapterRunning Setup Main Bios SetupPress the Delete key to enter Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System DateLBA Mode Control TypeMulti-Sector Transfers Native Mode Operation Transfer ModeUltra DMA Mode Sata Controller ModeSata Ahci Available when Sata RAID is Disabled System MemoryExtended Memory QuickBoot Mode Advanced SetupBoot Features QuietBoot ModePower Loss Control Acpi ModePower Button Behavior Memory Cache Cache System Bios AreaCache Extended Memory Cache Base 0-512KCache Base 512K-640K Discrete Mtrr AllocationPCI Parity Error Forwarding Default Primary Video AdapterEmulated IRQ Solutions Reset Conﬁguration DataLarge Disk Access Mode Enable MasterLatency Timer Serr Signal ConditionBranch 0/1 Rank Interleaving Memory Branch ModeHigh Temperature Dram Operation Branch 0/1 Rank Sparing Enabling Multi-Media Timer Crystal Beach Features Clock Spectrum Feature Snoop FilterAdvanced Processor Options CPU SpeedDCA Delay Clocks Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU Intel Eist Support Available when supported by the CPUMode Device ConﬁgurationSerial Port B Base I/O AddressBaud Rate Console RedirectionCOM Port Address Console TypeVoltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control ModesCPU Temperature Threshold See note on Temperature Monitoring Existing Event Log Number System Event LoggingClear System Event Logging Event Log ControlTimer for Loading OS Minutes System Event Log/System Event Log List ModeOS Boot Watch Dog Time Out OptionRealtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User PasswordBoot Password on BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupDevice IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM PassedSystem Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Important Notes to the User Intel HostRAID Setup GuidelinesIntroduction to Serial ATA and Parallel ATA Serial ATA SataIntel HostRAID Conﬁgurations Intel Matrix StorageUsing the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager UtilityInstalling Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations Chassis WeightPower Supply System CoolingRegulatory Compliance