Toshiba RBC-AMS41E owner manual Setting the current day of the week and clock time

Page 6

Setting the current day of the week and clock time

•Set the current clock time and day of the week.

•The day of the week and clock settings can be performed whether the air conditioner is running or shut down.

*The air conditioner continues to operate (run) while the day of the week and clock settings are being performed.

•The normal operation of the air conditioner or a program for a scheduled operation can be input even without performing the day of the week and clock settings, but the scheduled operation cannot be executed. In order to execute scheduled operations, the day of the week and clock must be set without fail.

•Before this remote controller is shipped from the factory, the initial setting (default) of the 24-hour display is established for the clock time display, but this can be changed to the 12-hour (AM/PM) display.

*If you want to use the 12-hour time display, refer to the “Selecting the remote controller functions” section.

*In these instructions, the 24-hour display is used in the figure and descriptions.

Preparations

Turn on the ground fault interrupter.

•When the power is turned on, a dividing line appears on the remote controller display.

*For about a minute after the power has been turned

on, on the LCD screen blinks, and there will be no response to the keys of the remote controller even when they are pushed.

1Hold down the button (48) for at least 4 seconds.

• The display transfers to the day of the week/clock setting screen.

• The whole LCD display blinks.

2 Repeatedly push the

button

<Blinks>

 

(45), and select the current day of the week.

• Move the day arrow to the position above the current day of the week.

• The LCD display continues to blink.

3Push the TIME and buttons (40), and select the current clock time.

•Each time the button (40) is pushed, the clock is moved forward by one minute.

•Each time the button (40) is pushed, the clock is moved back by one minute.

•When the or button is held down, the clock is moved forward or back in 10-minute increments.

•The LCD display continues to blink.

4Push the button (42) to return to the original screen.

•As soon as the button is pushed, the clock starts running. (Do this in synchronization with a time signal.)

• on the LCD screen goes off.

•After the clock has been set, the entire LCD screen lights, but the colon (“ ”) continues to blink.

G￿￿ ￿R￿￿ ￿U￿￿ ￿P￿￿ ￿A￿￿ ￿￿d .o .o .

EN

MB FRIGO Grupa d.o.o., Bani 81, 10010 Zagreb, www.toshiba.hr, e-mail: toshiba@mbfrigo.hr

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Remote controllerP Manual del propietario Mando a distanciaBedienungsanleitung Contents Safety precautions ImpactParts and their functions Parts and their functions Setting the current day of the week and clock time Correct operating procedures Procedure for normal operationCorrect operating procedures Symbol shown on the rightStarting the louver swing motion Now hold down the Temp button 49 for at least 4 seconds Self-cleaning operationsSave operations To release the save operation, push the button 38 againPush the Temp or button 49 to move the up/down grille Grille operation procedureDetailed settings Push the button 32 to stop the up/down grillePush the button How to set up the operation programsScheduled operations Push ButtonScheduled operations Example of setting up an operation program Scheduled operation setup Program check operation Error displaysCopying the program settings Push the button Again push the buttonEditing the operation programs Instructions for special holidaysHow to cancel the special holiday setting How to execute timer operations Timer operationsTimer operations Push the Time and buttons 40, and select the set timeTroubleshooting Selecting the remote controller functions Selecting the functions using the DIPSwitches of the remote controller Selecting the remote controller functions
Top Page Image Contents