Scheduled operations
•Scheduled operations for a
•Eight (01 to 08) operations for each day of the week can be set in a scheduled operation program (item settings).
–The following items can be set in a program:
a.Operation time
b.Operation start/stop
c.Operation mode
d.Temperature setting (frost protection)
e.Restriction on button operations
f.Save operation
•With a scheduled operation, the air conditioner is operated at the set operation time according to the program which has been set.
•The operation time can be set in
This function cancels the button operations while a scheduled operation is being executed. To use this function, refer to the “Selecting the remote controller functions” section and change the settings before proceeding with the program settings described below. The initial (factory) setting calls for no restriction on the button operations.
* Save operation
The save operation function is not provided for some models and systems. To find out whether the function is provided, consult your dealer or a contractor with specialized experience.
* Concerning the “Continue xx” setting
The “Continue” setting can be established for the operation start/stop, operation mode and temperature setting items. This setting causes the current operation modes of the indoor units to be continued.
* “Continue” is set on the initial screen for each item of each program number so in the example of the operation given above there is no need to input anything for the operation start/stop and operation mode items.
* This function does not work if the “timer operation function” or “no timer function” has been selected by following the steps set forth in the “Selecting the remote controller functions” section.
How to set up the operation programs
•Perform the steps below to set up a scheduled operation program (item settings).
*Programs can be set up whether the air conditioner is running or shut down.
*While these steps are being taken, an air conditioner which is operating continues to operate.
1Push the 
button (46).
•The display transfers to the program input screen.
•The entire LCD screen starts blinking.
2Push the 
button (45).
•Repeatedly push the button to move the day arrow to the position above the day of the week when
| the scheduled operation is to be executed. |
|
|
| |||||
3 Push the | button (42). | G R |
|
|
| ||||
|
|
|
|
|
|
|
| ||
• Set the day of the week when the scheduled | |||||||||
| operation is to be executed. |
|
|
| |||||
|
|
|
|
|
| ||||
• The days of the week display and the day arrow |
|
| |||||||
| |||||||||
| stop blinking and light up. | U |
|
|
| ||||
4 Push the | button (37). |
|
|
| |||||
|
|
|
|
| |||||
• Each time the button is pushed, the number on the | |||||||||
|
|
|
|
| P |
|
|
| |
| numeric display changes in the following |
|
|
| |||||
| sequence. |
|
|
|
|
|
| ||
• Stop pushing the button when the numberA | to be | ||||||||
| programmed blinks on the display. |
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| d . |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| * For the items inside the square parentheses, | ||||||||
|
|
|
|
| o. |
|
|
| |
| refer to the “Editing the operation programs” | ||||||||
| section. |
| o. |
|
|
| |||
5 Push the | button (42). |
|
|
| |||||
|
|
|
|
| |||||
•The program number on the numeric display stops blinking and lights up.
6 Push the TIME 
and 
buttons (40).
•Set the operation time. This time must be input.
•The steps taken are the same as for setting the clock.
* After setting the time, there is no need to push the 
button (42). All the items will be entered together in step 8.
MB FRIGO Grupa d.o.o., Bani 81, 10010 Zagreb, www.toshiba.hr,
10