Skip the Periodical Timer Recording, 46 EN

E3NG0FD_EN.book Page 46 Wednesday, January 30, 2008 10:37 AM

VPS (Video Programme System) / PDC (Programme Delivery Control)

The Video Programme System (VPS) or Programme Delivery Control (PDC) assures that the TV programmes you have programmed for timer recording are recorded exactly from beginning to end, even if the actual broadcasting time differs from the scheduled time due to a delayed start or extension of the programme duration. Furthermore, if a programme is interrupted, the recording will also be interrupted automatically and resumed when the programme starts again.

If the VPS/PDC signal drops out because the broadcast signal is weak, or if a broadcasting station does not transmit a regular VPS/PDC signal, the timer recording is performed in normal mode (without VPS/ PDC) even if it was programmed for VPS/PDC. If the starting time of the VPS/PDC timer recording is between 0:00 and 3:59 on a given day, the VPS/PDC function will operate from 20:00 on the previous day to 4:00 on the next day. If the starting time of the VPS/ PDC timer recording is between 4:00 and 23:59 on a given day, the VPS/PDC function will operate from 0:00 on the given day to 4:00 on the next day. This means that if the relevant programme is broadcasted within this period, it is recorded correctly. If the timer is not programmed correctly, the incorrect timer setting stays in effect unless you cancel it. To cancel an incorrect timer setting, refer to “Checking, Cancelling or Correcting the Timer Programming Information” on this page.

Note

• This feature is only available for analogue channels.

Checking, Cancelling or Correcting the Timer Programming Information

1 Press [TIMER PROG.].

2 A) To delete the timer programme:

1)Select the programme you want to delete using [U \ D], then press [ENTER].

2)Select “Delete” using [U \ D], then press [ENTER].

Confirmation window will appear.

3)Select “Yes” using [U \ D], then press

[ENTER].

B) To correct the timer programme:

1)Select the programme you want to correct using [U \ D], then press [ENTER].

2)Select “Programme Change” using [U \ D], then press [ENTER].

3)Correct the timer programme by using [U \ D \ L \ P], then press [ENTER].

3 Press [TIMER PROG.] to exit.

To check the timer programming in progress Press [TIMER PROG.].

Skip the Periodical Timer Recording

You can deactivate the periodical (Daily, Mon-Frior Weekly) timer recording temporarily.

1 In stop mode, press [TIMER PROG.].

2 Select the periodical timer recording programme you want to skip using [U \ D], then press [ENTER].

3 Select “Programme Change” using [U \ D], then press [ENTER].

4 Move the cursor to the “Skip” field using [L \ P], then select “ON” using [U \ D] and then press [ENTER] to activate the setting.

•“✔” will be displayed on the left side of the timer programme.

•The setting will go back to “OFF” after the programme is skipped once.

Stop the Timer Recording in Progress

On the front panel of the unit, press [C STOP] to stop the recording, or press and hold [STOP C] on the remote control for 2 seconds.

•You can also stop the timer recording in progress by deleting the timer programme. Press

[TIMER PROG.] while the timer recording is in progress, then follow steps 2-A)and 3 of the “Checking, Cancelling or Correcting the Timer Programming Information” on this page.

If the Timer Programming Did Not Complete Correctly

The error number appears on “Timer Programming” list.

Timer Programming

0:00 THU 06/12

	Date	Start	End	CH	STTL
	Date	Start	End	CH	VPS/PDC
E40	06/12	7:00	9:00	901

New Programme

1/1

The error programme will be displayed in gray with an error number.