Onkyo DV-SP1000 instruction manual Troubleshooting, This is because the i.LINK Output Setting is

Troubleshooting—Continued

	This is because the i.LINK Output Setting is
	set to Off. If the DV-SP1000/DV-SP1000E is
SACD audio is not output	properly connected to an i.LINK component	Set the i.LINK Output Setting to On (page 76).
	and an SACD is loaded, the IEEE 1394 indica-
by the i.LINK sockets?
	tor will flash.
	The i.LINK cables are not connected properly.	Check the i.LINK connections and correct as nec-
		essary (page 35).
SACD audio is not output	This is because the i.LINK Output Setting is
by the analog audio out-		Set the i.LINK Output Setting to Off (page 76).
	set to On.
puts?
	While the i.LINK Output Setting is set to On,
Can’t access the Analog	the Analog Audio Out Speaker Setting,	Set the i.LINK Output Setting to Off (page 76).
Audio Out settings?	Speaker Distance, and Test Tone settings have
	no effect and are unavailable.
Can’t play MP3 and JPEG	The disc is not ISO 9660 Level 2 format.	Use only ISO 9660 Level 2 format discs (page 10).
discs?	The disc has not been finalized.	Finalize the disc (page 10).
	MP3 files without a “.mp3” or “.MP3” file-	Use the correct filename extension (page 10).
	name extension are not recognized.
Can’t select MP3 files?
	The MP3 disc is a multisession disc.	Only files in the first session of a multisession disc
		can be played (page 10).
	JPEG files without a “.jpg” or “.JPG” or
	“.JPEG” filename extension are not recog-	Use the correct filename extension (page 10).
	nized.
	Only Baseline JPEG files are supported. Pro-	Use Baseline JPEG files (page 10).
Can’t view JPEG files?	gressive JPEG files are not.
	Only JPEG files with the following brightness/
	color difference ratios are supported: 4:4:4,	Use JPEG files with the supported ratio (page 10).
	4:2:2, and 4:1:1.
	The JPEG file is too big.	Use JPEG files that are less than 5 MB (page 10).
The message “NO PLAY”	The disc is dirty.	Remove the disc and clean it (page 11).
appears on the display?
		Turn off the DV-SP1000/DV-SP1000E, wait five
Buttons on the remote con-	Power supply voltage fluctuations and other	seconds, then turn it on again. If that doesn’t
	anomalies, such as static electricity, can inter-	resolve the issue, disconnect the power cord from
troller don’t work?
	fere with normal operation.	the wall outlet, wait five seconds, reconnect it, then
		try again.
	There are no batteries in the remote controller.	Install new batteries (page 14).
	The batteries are flat.	Replace with new batteries (page 14).
	The batteries are installed incorrectly.	Check the batteries and correct as necessary
		(page 14).
	You’re not pointing the remote controller at the	Point the remote controller at the DV-SP1000/
	DV-SP1000/DV-SP1000E’s remote sensor.	DV-SP1000E’s remote sensor (page 14).
Buttons on the		Use the remote controller closer to the
DV-SP1000/DV-SP1000E	You’re too far away from the DV-SP1000/	DV-SP1000/DV-SP1000E (page 14). The remote
work OK but those on the	DV-SP1000E.	controller has a range of approximately 16 ft. (5
remote controller don’t?		meters).
	A strong light source is interfering with the	Make sure that the DV-SP1000/DV-SP1000E is
		not subjected to direct sunshine or inverter-type flu-
	DV-SP1000/DV-SP1000E’s remote sensor.
		orescent lights. Relocate if necessary.
	If the DV-SP1000/DV-SP1000E is installed in
	a cabinet with colored glass doors, the remote	Open the doors, or use a cabinet without colored
	controller may not work reliably when the	glass.
	doors are closed.

94