Toshiba 51HX94 owner manual Device code setup, Searching and sampling the code of a device

Page 30

Chapter 3: Using the remote control

Programming the remote control to operate your other devices

Device code setup

1.Refer to the multi-brand remote control device code table on pages 32Ð33 to find the code for the brand of your device.

If more than one code is listed, try each one separately until you find the one that works.

2.Press MODE until the Mode indicator for the device (CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2) lights up.

3.While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code for your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4.Point the remote control at the device and press POWER to test the code.

If the device responds to the remote control: You have entered the correct code.

If the device does not respond to the remote control:

You may have entered the wrong code. Repeat steps 3 and 4 using another code.

Note: In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device).

If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

5. Press MODE to select the TV mode to control the TV.

Note:

Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device.

Each time you change the batteries you will need to reprogram the remote control.

Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1.Press MODE to select the mode you want to set up.

2.While holding down RECALL, press 8 Ð 5 Ð 0 Ð 0. The remote control will enter program mode.

3.Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4.If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER.

Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

POWER

Numbers

MODE

+10

ACTION 100 MENU

y

ENTER

VOL y/z

RECALL

30

Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.

 

51,57HX94(E)026-33

30

9/12/04, 7:04 PM

Image 30
Contents 51HX94 57HX94 Issue Safety PrecautionsIt Makes a Difference Where Your TV Stands Tune Into SafetyImportant Safety Instructions Installation, Care, and ServiceAlways place the TV on the floor Care Contents 102 Features of your new TV IntroductionWelcome to Toshiba Introduction TV front panel controls and connections Connecting your TVPower Ñ Press to turn the TV on and off 6 7 8TV back panel connections For an explanation of cable types, seeOverview of cable types To a Personal Computer PCFor more information, call your local Cable operator Connecting a digital CableCARDAbout the connection illustrations You will needTo use the TV Guide On Screen recording features Connecting a VCR and antenna or Cable TV no Cable boxConnecting a camcorder To view the VCRConnecting a VCR and Cable box On Screen recording featuresTo view basic and premium Cable channels Connecting a VCR and satellite receiver To view satellite programs using the standardVideo connections or to record satellite programs To view premium Cable channels To view the DVD playerTo view VCR Two coaxial cables To view antenna or Cable channelsTo record a TV program while watching a DVD Connecting two VCRs To connect Hdmi devices, you will need Connecting an Hdmi or a DVI device to the Hdmi input¥ one Hdmi cable type a connector for each device To connect DVI devices, you will needOne optical audio cable Connecting a digital audio systemConnecting an analog audio system To control the audioTo connect the IR blaster cable IEEE-1394 devices using On-screen control iconsTheaterNet on-screen device control To control the devicesConnecting IEEE-1394 video devices Supported signalsWhen you connect a D-VHS or A/V HD device to the TV IEEE-1394 device initializationIEEE-1394 device management To edit the IEEE-1394 device informationLINKconnection To connect to the G-LINK jackSee Chapter Using the remote control Learning about the remote controlInstalling the remote control batteries To install the remote control batteriesDevice mode control after programming Remote Control functional key chart PowerAudio VCR Mute Press Mode to select the mode you want to set up Device code setupPress Mode to select the TV mode to control the TV Searching and sampling the code of a deviceRepeatedly press Mode to select CABLE/SAT mode Using the volume lock featureOperational feature reset To reset the volume controls to the original device modeMulti-brand remote control device codes VCRs/PVRsCable boxes Laser disks CD playersReceivers DVD playersMenu layout and navigation Main menu layoutSetup / Installation menu layout Screen 3 Do you have Cable service connected? TV Guide On Screen system setupTo set up the TV Guide On Screen system Screen 4 Do you have a Cable box connected?Setting up the TV Guide On Screen system On nextSetting up the TV Guide On Screen system TV Guide On Screen Reminder To configure the ANT 1 and ANT 2 input sources Setting up your TVSelecting the menu language Configuring the antenna input To select the menu languageProgramming channels into the TV’s channel memory Programming channels automaticallyTo program channels automatically Manually adding and deleting channels in the channel memory To clear your favorite channel lists Programming your favorite channelsTo add and delete channels in the Favorite Channels lists To tune your favorite channels for the current ANT inputTo set up TheaterNet device control Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To remove a device from TheaterNetTo select the device’s control icons directly To close the on-screen control iconsTo view another source Laser disk players TheaterNet IR device codesAmplifiers Miscellaneous audio devicesVideo accessory Hdtv decoder Receivers VCRsSTS Automatically adjusting the color Adjusting the color convergenceManually adjusting the color Convergence using TouchFocusTo reset your convergence adjustments Setting the Avhd device skip timeSelecting the Hdmi 1 or Hdmi 2 audio mode To select the Hdmi audio modeTo set the time and date Setting the time and dateViewing the CableCARD menu To view the CableCARD menuViewing the digital signal meter Viewing the system statusBelow TV Guide On Screen system includes the following featuresTo open the TV Guide On Screen system Rating, stereo, HDTV, new episodeTV Guide On Screen remote control functions Navigating the TV Guide On Screen systemVideo Window Panel MenusTo lock/unlock the Video Window Info Box TV Guide On Screen IconsTV Guide On Screen Services Listings screenSearch screen Example Category searchList of all matching shows for that keyword is displayed To edit or delete a keywordTo view a recording, you can do one of the following Recordings screenTo choose the way recordings are displayed Screen a Screen BRecord features Set a show to Record from a panel menuSchedule screen Manually set a show to Record Recording notification bannerRemind features Set a show Reminder from a panel menuManually set a show Reminder Reminder notification banner Setup screen Change system settingsChange channel display Record defaults Change default optionsGeneral default options Remind defaultsUsing the TV’s features Selecting the video input source to viewTo select the video input source to view Labeling the video input sources To label the video input sourcesTo clear the input labels Switching between two channels using Channel Return Tuning channelsTuning to the next programmed channel Switching between two channels using SurfLockPress PIC Size on the remote control Selecting the picture sizeTo select the picture size TheaterWide 2 picture size for letter box programs ¥ None of the picture is hiddenTheaterWide 1 picture size For 43 format program Full picture size for 169 480i, 480p source programs onlyTo turn on the Auto Aspect feature Using the auto aspect ratio featureTo set the scroll settings To turn off the Auto Aspect featureTo set the Cinema Mode to Video Selecting the display format 480i and 480p signals onlyTo set the Cinema Mode to Film To select the display formatTo display a program in the POP window Using the POP featuresUsing the POP double-window feature To close the POP windowSwitching the speaker audio main or POP Freezing the main picture in the POP double-windowTo close the still POP window Using the favorite channel scan feature POP double-window aspect ratioTo scan and tune your favorite channels Adjusting the picture quality Adjusting the pictureSelecting the picture mode Resetting the picture settingsUsing the Night Mode feature Using CableClear DNR digital noise reductionAdjusting the Velocity Scan Modulation Selecting the color temperatureResetting the advanced picture settings To select the color temperatureUsing the closed caption mode Digital closed captionsAdvanced closed captions Muting the sound Adjusting the audioDigital audio selector Selecting stereo/SAP broadcastsUsing the StableSound feature Turning off the built-in speakersUsing the SRS WOW surround sound feature Selecting the optical audio output formatUsing the memory card picture viewer Memory card specificationsTo set the slide show interval Viewing digital photos on your TVDuring the slide show To close the picture viewerUsing the memory card picture Setting the ON/OFF timerMemory card care and handling Understanding the auto power off feature Setting the sleep timerDisplaying TV setting information on-screen Understanding the last mode memory featureIf you cannot remember your PIN code Using the Locks menuEntering the PIN code Changing your PIN codePress z to highlight Edit Rating Limits and press Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Edit Rating Limits screen below appearsBlocking channels Unlocking programs temporarilyLocking video inputs Using the GameTimer Using the front panel lock featureTroubleshooting ¥ Adjust the picture qualitiesTroubleshooting TV Guide On Screen FAQs LED indicationsSetup How do I resize or close the Info window? Operations What do the frequencies for Record and Remind mean?Specifications AppendixLimited United States Warranty Limited Canada Warranty For 32 and Larger TVs101 12Ð25 IndexChannel programming 3Ð5Picture-out-picture POP Picture adjustmentsRemote control 2Ð5Toshiba America Consumer PRODUCTS, L.L.C 23566378