Toshiba 51HX94 owner manual Programming channels into the TV’s channel memory

Page 41

Chapter 6: Setting up your TV

Programming channels into the TV’s channel memory

When you press CHANNEL y or z on the remote control or TV front panel, your TV will stop only on the channels stored in the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels.

Note:

You must configure the antenna input sources before programming channels (see page 40).

The automatic channel programming process does NOT erase channels that were previously programmed into the TV’s memory, but adds newly found channels to the existing set of programmed channels. To remove a channel from the memory, you must manually delete it (see next page).

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

Programming channels for an antenna input configured for CABLE will take substantially longer than for an antenna input configured for ANTENNA. This is normal; however, once channel programming is completed, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

If you have a CableCARD inserted (page 12), channel programming for ANT 1 is disabled because the CableCARD automatically loads the Cable channel list in the TV’s channel memory.

To program channels automatically:

1.Make sure you have configured the antenna input sources. See page 41 for details.

2.Press MENU and open the SETUP menu.

3.Highlight INSTALLATION and press ENTER. (A new set of INSTALLATION menu icons will appear on-screen.

Setup

Installation

 

 

 

 

 

 

 

Sleep Timer

 

 

 

 

 

 

 

On/Off Timer

 

 

 

 

 

 

 

HDMI Audio Selection

 

Auto

 

 

Side Show Interval

 

2 Sec

 

 

 

 

AVHD Skip Time

 

15 min

 

 

 

 

Convergence

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD RTN

 

 

 

 

 

Navigate

 

Select

 

Back

EXIT

Exit

 

 

 

CH RTN

4.Open the TERRESTRIAL menu, highlight CHANNEL PROGRAM, and press ENTER.

5.Highlight ANT 1 or ANT 2, depending on which antenna input you want to program channels for, and then press ENTER to start automatic channel programming.

 

 

 

 

 

 

 

 

 

ANT 1

Antenna

Terrestrial

 

 

 

 

 

 

Scanning channels,please wait ...

Input Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

39%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel program

 

 

 

 

 

 

 

 

 

 

Abort

Channel Add/Delete

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal Meter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD RTN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Navigate

 

Select

Back

EXIT

Exit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CH RTN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The TV will automatically cycle through all the channels for the antenna input you selected, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above right).

To cancel channel programming, either press EXIT or highlight ABORT in the on-screen display and press

ENTER.

6.When channel programming is done, press CHANNEL y or z to view the programmed channels.

(Continued on next page)

Channel

Numbers

+10

ACTION 100 MENU

ENTER

CHANNEL yz

TV front panel

MENU VOLUMECHANNEL

EXIT TV/VIDEO TouchFocus

CHANNEL z / y

Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.

41

 

51,57HX94(E)040-43

41

9/12/04, 7:09 PM

Image 41
Contents 51HX94 57HX94 It Makes a Difference Where Your TV Stands Safety PrecautionsIssue Tune Into SafetyAlways place the TV on the floor Important Safety InstructionsInstallation, Care, and Service Care Contents 102 Welcome to Toshiba Features of your new TVIntroduction Introduction Power Ñ Press to turn the TV on and off Connecting your TVTV front panel controls and connections 6 7 8For an explanation of cable types, see TV back panel connectionsTo a Personal Computer PC Overview of cable typesAbout the connection illustrations Connecting a digital CableCARDFor more information, call your local Cable operator You will needConnecting a camcorder Connecting a VCR and antenna or Cable TV no Cable boxTo use the TV Guide On Screen recording features To view the VCRTo view basic and premium Cable channels Connecting a VCR and Cable boxOn Screen recording features Video connections or to record satellite programs Connecting a VCR and satellite receiverTo view satellite programs using the standard To view VCR To view premium Cable channelsTo view the DVD player To record a TV program while watching a DVD Two coaxial cablesTo view antenna or Cable channels Connecting two VCRs ¥ one Hdmi cable type a connector for each device Connecting an Hdmi or a DVI device to the Hdmi inputTo connect Hdmi devices, you will need To connect DVI devices, you will needConnecting an analog audio system Connecting a digital audio systemOne optical audio cable To control the audioTheaterNet on-screen device control IEEE-1394 devices using On-screen control iconsTo connect the IR blaster cable To control the devicesSupported signals Connecting IEEE-1394 video devicesIEEE-1394 device initialization When you connect a D-VHS or A/V HD device to the TVTo edit the IEEE-1394 device information IEEE-1394 device managementSee Chapter LINKconnectionTo connect to the G-LINK jack Learning about the remote control Using the remote controlDevice mode control after programming Installing the remote control batteriesTo install the remote control batteries Power Remote Control functional key chartAudio VCR Mute Press Mode to select the TV mode to control the TV Device code setupPress Mode to select the mode you want to set up Searching and sampling the code of a deviceOperational feature reset Using the volume lock featureRepeatedly press Mode to select CABLE/SAT mode To reset the volume controls to the original device modeCable boxes Multi-brand remote control device codesVCRs/PVRs Receivers CD playersLaser disks DVD playersMain menu layout Menu layout and navigationSetup / Installation menu layout To set up the TV Guide On Screen system TV Guide On Screen system setupScreen 3 Do you have Cable service connected? Screen 4 Do you have a Cable box connected?On next Setting up the TV Guide On Screen systemSetting up the TV Guide On Screen system TV Guide On Screen Reminder Selecting the menu language Configuring the antenna input Setting up your TVTo configure the ANT 1 and ANT 2 input sources To select the menu languageTo program channels automatically Programming channels into the TV’s channel memoryProgramming channels automatically Manually adding and deleting channels in the channel memory To add and delete channels in the Favorite Channels lists Programming your favorite channelsTo clear your favorite channel lists To tune your favorite channels for the current ANT inputSetting up TheaterNet Setting up and using TheaterNet on-screen device controlTo set up TheaterNet device control To remove a device from TheaterNetTo view another source To select the device’s control icons directlyTo close the on-screen control icons Amplifiers TheaterNet IR device codesLaser disk players Miscellaneous audio devicesVCRs Video accessory Hdtv decoder ReceiversSTS Manually adjusting the color Adjusting the color convergenceAutomatically adjusting the color Convergence using TouchFocusSelecting the Hdmi 1 or Hdmi 2 audio mode Setting the Avhd device skip timeTo reset your convergence adjustments To select the Hdmi audio modeViewing the CableCARD menu Setting the time and dateTo set the time and date To view the CableCARD menuViewing the system status Viewing the digital signal meterTo open the TV Guide On Screen system TV Guide On Screen system includes the following featuresBelow Rating, stereo, HDTV, new episodeNavigating the TV Guide On Screen system TV Guide On Screen remote control functionsTo lock/unlock the Video Window Video WindowPanel Menus TV Guide On Screen Icons Info BoxListings screen TV Guide On Screen ServicesExample Category search Search screenTo edit or delete a keyword List of all matching shows for that keyword is displayedTo choose the way recordings are displayed Recordings screenTo view a recording, you can do one of the following Screen a Screen BSchedule screen Record featuresSet a show to Record from a panel menu Recording notification banner Manually set a show to RecordManually set a show Reminder Remind featuresSet a show Reminder from a panel menu Reminder notification banner Change channel display Setup screenChange system settings General default options Change default optionsRecord defaults Remind defaultsTo select the video input source to view Using the TV’s featuresSelecting the video input source to view To clear the input labels Labeling the video input sourcesTo label the video input sources Tuning to the next programmed channel Tuning channelsSwitching between two channels using Channel Return Switching between two channels using SurfLockTo select the picture size Press PIC Size on the remote controlSelecting the picture size TheaterWide 1 picture size For 43 format program ¥ None of the picture is hiddenTheaterWide 2 picture size for letter box programs Full picture size for 169 480i, 480p source programs onlyTo set the scroll settings Using the auto aspect ratio featureTo turn on the Auto Aspect feature To turn off the Auto Aspect featureTo set the Cinema Mode to Film Selecting the display format 480i and 480p signals onlyTo set the Cinema Mode to Video To select the display formatUsing the POP double-window feature Using the POP featuresTo display a program in the POP window To close the POP windowTo close the still POP window Switching the speaker audio main or POPFreezing the main picture in the POP double-window To scan and tune your favorite channels Using the favorite channel scan featurePOP double-window aspect ratio Selecting the picture mode Adjusting the pictureAdjusting the picture quality Resetting the picture settingsUsing CableClear DNR digital noise reduction Using the Night Mode featureResetting the advanced picture settings Selecting the color temperatureAdjusting the Velocity Scan Modulation To select the color temperatureAdvanced closed captions Using the closed caption modeDigital closed captions Digital audio selector Adjusting the audioMuting the sound Selecting stereo/SAP broadcastsTurning off the built-in speakers Using the StableSound featureSelecting the optical audio output format Using the SRS WOW surround sound featureMemory card specifications Using the memory card picture viewerDuring the slide show Viewing digital photos on your TVTo set the slide show interval To close the picture viewerMemory card care and handling Using the memory card pictureSetting the ON/OFF timer Displaying TV setting information on-screen Setting the sleep timerUnderstanding the auto power off feature Understanding the last mode memory featureEntering the PIN code Using the Locks menuIf you cannot remember your PIN code Changing your PIN codeTo block and unblock TV programs and movies Blocking TV programs and movies by rating V-ChipPress z to highlight Edit Rating Limits and press Edit Rating Limits screen below appearsLocking video inputs Blocking channelsUnlocking programs temporarily Using the front panel lock feature Using the GameTimer¥ Adjust the picture qualities TroubleshootingTroubleshooting LED indications TV Guide On Screen FAQsSetup How do I resize or close the Info window? What do the frequencies for Record and Remind mean? OperationsAppendix SpecificationsLimited United States Warranty For 32 and Larger TVs Limited Canada Warranty101 Channel programming Index12Ð25 3Ð5Remote control Picture adjustmentsPicture-out-picture POP 2Ð523566378 Toshiba America Consumer PRODUCTS, L.L.C