Toshiba 51HX94 owner manual Connecting a VCR and satellite receiver

Chapter 2: Connecting your TV

Connecting a VCR and satellite receiver

Note: The TV Guide On Screen® system does not receive program listings from or for any satellite service.

Stereo VCR

You will need:

￿three coaxial cables

￿one set of component video cables (if your satellite receiver does not have component video, connect the standard A/V cables only)

￿three sets of standard A/V cables

From antenna

		VIDEO
IN from ANT	CH 3	L	R	IN
	CH 4
OUT to TV		L	R	OUT

￿

•For better picture performance, if your satellite receiver and VCR have S-video, connect S-video cables (plus the audio cables) instead of the standard video cables. Do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

•If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s AUDIO OUT jack using the white audio cable only.

To view satellite programs using the component video connections:

TV
	VIDEO 1	VIDEO 2	COLOR	COLOR
			STREAM	STREAM
			HD-1	HD-2
OUT 1	S-VIDEO	S-VIDEO
			Y	Y
OUT 2				PB
TheaterNet
		VIDEO		PR
	L/	L/
		MONO
		AUDIO		AUDIO
	R	R	R

IN
AUDIO
R	L
2
1
VIDEO
L/
MONO
AUDIO
R

TheaterNet

IEEE1394

1

2

HDMI IN

2

1

G-LINK

EJECT

CableCARD™

ANT1
(CABLE)
ANT2
ANT (75	)

Select the ColorStream HD-1 video input	From
source on the TV.*
	satellite

IN

OUT

DIGITAL AUDIO OUT

￿

dish

To view satellite programs using the standard

video connections or to record satellite programs:

Turn on all three devices. Set the VCR to the appropriate line input (refer to your VCR ownerÕs manual for details). Select the VIDEO 2 video input source on the TV.*

Y	PB	PR
Satellite
IN
S-VIDEO COMPONENT VIDEO			VIDEO
OUT			OUT
Satellite receiver

AUDIO L OUT L

R R

￿To view the VCR or view and record antenna channels:

Turn ON the VCR. Select the ANT-1 video input source on the TV.*

Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

or... Turn ON the VCR. Tune the VCR to the channel you want to watch. Select the VIDEO 1 video input source on the TV.*

_____________

*To select the video input source, press INPUT on the remote control (see page 67). To program the TV remote control to operate other devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

￿To use the TV Guide On Screen recording features:

1.Connect the G-LINK cable according to the instructions on page 25.

2.Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3.Set the VCR to the appropriate line input (refer to your VCR ownerÕs manual for details), and then turn OFF the VCR.

4.See Chapter 5 for details on setting up the TV Guide On Screen system.

5.See Chapter 7 for details on using the TV Guide On Screen system.

Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 15

51,57HX94(E)012-25 15 9/12/04, 7:01 PM