Toshiba TLP561, TLP260 Loading batteries, Open the cover, Install the batteries, Attach the cover

Page 15

Loading batteries

CONTENTS

15

Notes

Using batteries incorrectly can cause them to leak or burst. Strictly observe the following.

Install the batteries with their + and – ends facing correctly.

Do not charge, heat, disassemble, or short the batteries or throw them into a fire.

Do not leave any exhausted batteries in the remote control.

Do not mix different types of batteries or new and old batteries.

When you will not be using the remote control for a prolonged period, take the batteries out of the remote control.

When the remote control stops working or only works at very close range, replace all the batteries with new ones.

When replacing the batteries, use longer life alkaline batteries.

If a battery has leaked, carefully wipe off any residue inside the battery case before loading new batteries.

1

Bottom side

Open the cover.

 

2

Install the batteries.

Make sure that the +/– polarities match the

illustration in the compartment.

Before use

3

Attach the cover.

 

Image 15
Contents TLP560/TLP260 TLP260Safety Precautions Exemption Clauses Save Original Packing MaterialsAvoid Volatile Liquid Moisture CondensationPower Sources Source of LightVentilation Important Safety Instructions Stack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Damage Requiring ServiceReplacement Parts Safety CheckDo not look into the arm light while it is lit Do not carry by the camera armHeat could erase or discolor the letters on a thermal paper Do not move the projector while the arm is still erectBefore Power supply cord selectionContents Names of each part on the main unit SpeakerLens Carrying handleAnti-theft lock hole ON/STANDBY button Names of each part on the main unitComputer OUT connector USB connectorControl connector 26 72 RS-232C connector Video in connectorFreeze button Names of each part on the remote controlAttach the cover Install the batteriesLoading batteries Open the coverFront side Rear side Remote control operationFloor-mounted projector placement Side view Determine the screen size projected on the screenConnect the power cord Take off the lens coverInsert the other end into a wall outlet Lens shift function Turn clockwise to lift up Turn counterclockwise to lower Turn the foot adjuster to make fine adjustment to the heightCeiling-mounted projector placement Connecting a computer Audio in jack Connecting video equipmentSet for use as analog RGB input Projector operation control by a computer How to use the output connector Press ON/STANDBY Remote controlLamp indicator blinks while the lamp is warming up Projection on the screenLanguage Turn on the connected equipment and put it in playback modePress Enter to confirm Control panel Main unit sideInput source selection menu appears Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Press EnterFocus on the picture by turning Adjust the picture size by turningFocusing ring Zooming leverPress VOL/ADJ +/- to adjust volume Press the + button to increase volumePress the button to decrease volume Turning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Press Auto SET Adjusting the picture automaticallyInput full screen video signals from the input Source computer and project the imagePress Keystone Adjust the distortion with the selection buttonsTo finish the adjustment, press Exit repeatedly Correcting the keystone distortionSound and picture are cut off temporarily Icon appears in the mute modeCutting off the picture and sound temporarily Press MutePicture freezes Icon appears in the freeze modeFreezing the picture Press FreezeTo reduce the enlargement ratio, press the Resize button Icon appears in the resize modeEnlarging the picture size Press ResizeDisplaying PIP Sub-pictures Press PIPSub-picture is displayed Press Call Displaying InformationStart a presentation on the computer Operating the presentation modeChange a slide with the selection buttons Adjust the projector before presentation if necessarySelect the computer input with Input Press P.MODE and hold for two secondsPress Menu Operating the menu screenStart Adjust with VOL/ADJ +/- or selection buttonsAdjust the image flicker Guide Menu adjustments and settingsReset Full Menu adjustments and settings PictureFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Menu background is normal Reset Full Menu adjustments and settings DisplayFull Menu settings Default setting Full Menu settings Reset PIP menu setting ImagingDocument camera Part names of the document imaging camera modelPreparation of the document imaging camera Light turns on Press ARM LightSet a document to be projected Camera control panelPicture projection with the document imaging camera Press Camera to select the camera input modePut back the arm When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Camera subject which is too dark or vividLocking the white balance Project a white paper and enlarge it to fillScreen Paper or cloth Correcting illuminated defectsWith the document camera operating, fully Cover the camera lens with a piece of blackMain unit side IndicatorsTrouble indications Control panelDetach the air filter Air filter cleaningUnplug the power cord Take off the front cover Clean the air filterMount the air filter and the filter frame Mount the front coverLens side to fix it Replacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitPull out the lamp Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Take off the lamp cover on the bottom panelSlide the cover into place and tighten the two screws Reset the lamp timerLoad a new lamp Attach the lamp coverSymptom Cause Correction Before calling service personalBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable computer signal Applicable signalCompatible Video and S-Video signal Applicable signalSignal assignment of RS-232C Interface format Controlling the projector by using RS-232CControlling the projector by using RS-232C VLU Computer Resize Main unit SpecificationsReplacement lamp Specifications