Toshiba TLP260 Press ARM Light, Set a document to be projected, Camera control panel, Document

Page 56

Picture projection with the document imaging camera

CONTENTS

56

CAUTION

Do not look into the arm light while it is lit.

Camera control panel

LOCK

W.BALANCE

ARM LIGHT

1

 

CAMERA

CAMERA

GAIN

Preparation

1Project a picture on the screen as explained in the step “Projection on the screen”. 28

1

ARM LIGHT

Press ARM LIGHT.

 

 

 

2

 

The light turns on.

 

 

Set a document to be projected.

 

 

 

 

 

 

Place the document (illustrations, etc.) onto or around the

 

 

projector, and turn the camera head to the direction of the

 

 

document.

 

 

 

Images on the screen

 

 

123

123

 

 

 

 

 

123

123

 

 

 

 

 

Setting direction

Notes

Do not leave documents on the unit or near of the air exhaust for long periods of time. The heat could erase or discolor the letters on a thermal paper.

Use the arm light when necessary according to the brightness of the room.

Continued

imagingDocument camera

Image 56
Contents TLP260 TLP560/TLP260Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Exemption ClausesVentilation Power SourcesSource of Light Important Safety Instructions Accessories Object and Liquid EntryDo not place the product vertically Stack InhibitedDamage Requiring Service Replacement PartsSafety Check ServicingDo not carry by the camera arm Heat could erase or discolor the letters on a thermal paperDo not move the projector while the arm is still erect Do not look into the arm light while it is litPower supply cord selection BeforeContents Anti-theft lock hole Names of each part on the main unitSpeakerLens Carrying handle Names of each part on the main unit ON/STANDBY buttonUSB connector Control connector 26 72 RS-232C connectorVideo in connector Computer OUT connectorNames of each part on the remote control Freeze buttonInstall the batteries Loading batteriesOpen the cover Attach the coverRemote control operation Front side Rear sideFloor-mounted projector placement Determine the screen size projected on the screen Side viewInsert the other end into a wall outlet Connect the power cordTake off the lens cover Lens shift function Turn the foot adjuster to make fine adjustment to the height Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Connecting a computer Connecting video equipment Audio in jackSet for use as analog RGB input Projector operation control by a computer How to use the output connector Remote control Lamp indicator blinks while the lamp is warming upProjection on the screen Press ON/STANDBYTurn on the connected equipment and put it in playback mode Press Enter to confirmControl panel Main unit side LanguageSelect the input source by pressing Input repeatedly Press Input and hold for two secondsPress Enter Input source selection menu appearsAdjust the picture size by turning Focusing ringZooming lever Focus on the picture by turningPress the button to decrease volume Press VOL/ADJ +/- to adjust volumePress the + button to increase volume Press ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Adjusting the picture automatically Input full screen video signals from the inputSource computer and project the image Press Auto SETAdjust the distortion with the selection buttons To finish the adjustment, press Exit repeatedlyCorrecting the keystone distortion Press KeystoneIcon appears in the mute mode Cutting off the picture and sound temporarilyPress Mute Sound and picture are cut off temporarilyIcon appears in the freeze mode Freezing the picturePress Freeze Picture freezesIcon appears in the resize mode Enlarging the picture sizePress Resize To reduce the enlargement ratio, press the Resize buttonSub-picture is displayed Displaying PIP Sub-picturesPress PIP Displaying Information Press CallOperating the presentation mode Start a presentation on the computerAdjust the projector before presentation if necessary Select the computer input with InputPress P.MODE and hold for two seconds Change a slide with the selection buttonsOperating the menu screen Press MenuAdjust with VOL/ADJ +/- or selection buttons StartGuide Menu adjustments and settings Adjust the image flickerFull Menu adjustments and settings Picture ResetFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Menu background is normal ResetFull Menu settings Default setting Full Menu settings Reset PIP menu setting Part names of the document imaging camera model ImagingDocument cameraPreparation of the document imaging camera Press ARM Light Set a document to be projectedCamera control panel Light turns onPress Camera to select the camera input mode Picture projection with the document imaging cameraWhen finished, turn off the light and close it Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Put back the armScreen Locking the white balanceProject a white paper and enlarge it to fill Correcting illuminated defects With the document camera operating, fullyCover the camera lens with a piece of black Paper or clothIndicators Trouble indicationsControl panel Main unit sideAir filter cleaning Unplug the power cord Take off the front coverClean the air filter Detach the air filterLens side to fix it Mount the air filter and the filter frameMount the front cover Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filterLamp replacement Unplug the power cord Wait until the lamp gets cool enoughTake off the lamp cover on the bottom panel Pull out the lampReset the lamp timer Load a new lampAttach the lamp cover Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable signal Applicable computer signalApplicable signal Compatible Video and S-Video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C VLU Computer Resize Specifications Main unitSpecifications Replacement lamp