Toshiba TLP261 Object and Liquid Entry, Do not place the product vertically, Stack Inhibited

Page 6

IMPORTANT SAFETY INSTRUCTIONS (continued)

CONTENTS

6

11.Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short- out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

12.Do not place the product vertically

Do not use the product in the upright position to project the pictures at the ceiling, or any other vertical positions. It may fall down and dangerous.

13.Stack Inhibited

Do not stack other equipment on this product or do not place this product on the other equipment.

Top and bottom plates of this product develops heat and may give some undesirable damage to other unit.

14.Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

15.Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

S3125A

Before use

Continued

Image 6
Contents TLP260 TLP560/TLP260Safety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Exemption ClausesPower Sources Source of LightVentilation Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedSafety Check Damage Requiring ServiceReplacement Parts ServicingDo not move the projector while the arm is still erect Do not carry by the camera armHeat could erase or discolor the letters on a thermal paper Do not look into the arm light while it is litPower supply cord selection BeforeContents Names of each part on the main unit SpeakerLens Carrying handleAnti-theft lock hole Names of each part on the main unit ON/STANDBY buttonVideo in connector USB connectorControl connector 26 72 RS-232C connector Computer OUT connectorNames of each part on the remote control Freeze buttonOpen the cover Install the batteriesLoading batteries Attach the coverRemote control operation Front side Rear sideFloor-mounted projector placement Determine the screen size projected on the screen Side viewConnect the power cord Take off the lens coverInsert the other end into a wall outlet Lens shift function Turn the foot adjuster to make fine adjustment to the height Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Connecting a computer Connecting video equipment Audio in jackSet for use as analog RGB input Projector operation control by a computer How to use the output connector Projection on the screen Remote controlLamp indicator blinks while the lamp is warming up Press ON/STANDBYControl panel Main unit side Turn on the connected equipment and put it in playback modePress Enter to confirm LanguagePress Enter Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Input source selection menu appearsZooming lever Adjust the picture size by turningFocusing ring Focus on the picture by turningPress VOL/ADJ +/- to adjust volume Press the + button to increase volumePress the button to decrease volume Turning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Source computer and project the image Adjusting the picture automaticallyInput full screen video signals from the input Press Auto SETCorrecting the keystone distortion Adjust the distortion with the selection buttonsTo finish the adjustment, press Exit repeatedly Press KeystonePress Mute Icon appears in the mute modeCutting off the picture and sound temporarily Sound and picture are cut off temporarilyPress Freeze Icon appears in the freeze modeFreezing the picture Picture freezesPress Resize Icon appears in the resize modeEnlarging the picture size To reduce the enlargement ratio, press the Resize buttonDisplaying PIP Sub-pictures Press PIPSub-picture is displayed Displaying Information Press CallOperating the presentation mode Start a presentation on the computerPress P.MODE and hold for two seconds Adjust the projector before presentation if necessarySelect the computer input with Input Change a slide with the selection buttonsOperating the menu screen Press MenuAdjust with VOL/ADJ +/- or selection buttons StartGuide Menu adjustments and settings Adjust the image flickerFull Menu adjustments and settings Picture ResetFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Menu background is normal ResetFull Menu settings Default setting Full Menu settings Reset PIP menu setting Part names of the document imaging camera model ImagingDocument cameraPreparation of the document imaging camera Camera control panel Press ARM LightSet a document to be projected Light turns onPress Camera to select the camera input mode Picture projection with the document imaging cameraCamera subject which is too dark or vivid When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Put back the armLocking the white balance Project a white paper and enlarge it to fillScreen Cover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothControl panel IndicatorsTrouble indications Main unit sideClean the air filter Air filter cleaningUnplug the power cord Take off the front cover Detach the air filterMount the air filter and the filter frame Mount the front coverLens side to fix it Cleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterTake off the lamp cover on the bottom panel Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Pull out the lampAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable signal Applicable computer signalApplicable signal Compatible Video and S-Video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C VLU Computer Resize Specifications Main unitSpecifications Replacement lamp