Toshiba TLP561, TLP260, TLP560, TLP261 owner manual Connecting a computer

Page 23

Connecting a computer

CONTENTS

You can project the picture from the computer.

Check that the power supplies for the projector and for the computer are off before connecting the cables.

COMPUTER IN connector

For use as both analog RGB and Y/PB/PR input. At shipping from factory, it is set for use as analog RGB input.

			VIDEO IN S-VIDEO IN	COMPUTER OUT	COMPUTER IN
CONTROL	USB	AUDIO IN	VIDEO IN S-VIDEO IN	( Y/PB/PR )	( Y/PB/PR )

AUDIO IN jack

For use as audio signal of all input sources.

Computer

23

connectionsInstallation and

To COMPUTER IN connector Be sure to connect in the proper direction.

To monitor port

RGB cable (supplied)

To AUDIO IN jack Audio cable (supplied)

ø3.5mm stereo mini-jack To audio output port

Notes

•The projector cannot be connected to a computer without an analog RGB connector. For details, refer to the computer manual.

•You may not be able to connect some computers to the projector. For details, consult the dealer.

•When connecting to a Macintosh computer, some models may need a Mac adapter for connection.

•Some computers may have output modes which are not compatible with this projector. Check the compatibility of the connectors, signal levels, timing, resolutions, etc.

Image 23

Contents TLP560/TLP260 TLP260Safety Precautions Exemption Clauses Save Original Packing MaterialsAvoid Volatile Liquid Moisture CondensationVentilation Power SourcesSource of Light Important Safety Instructions Stack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Damage Requiring ServiceReplacement Parts Safety CheckDo not look into the arm light while it is lit Do not carry by the camera armHeat could erase or discolor the letters on a thermal paper Do not move the projector while the arm is still erectBefore Power supply cord selectionContents Anti-theft lock hole Names of each part on the main unitSpeakerLens Carrying handle ON/STANDBY button Names of each part on the main unitComputer OUT connector USB connectorControl connector 26 72 RS-232C connector Video in connectorFreeze button Names of each part on the remote controlAttach the cover Install the batteriesLoading batteries Open the coverFront side Rear side Remote control operationFloor-mounted projector placement Side view Determine the screen size projected on the screenInsert the other end into a wall outlet Connect the power cordTake off the lens cover Lens shift function Turn clockwise to lift up Turn counterclockwise to lower Turn the foot adjuster to make fine adjustment to the heightCeiling-mounted projector placement Connecting a computer Audio in jack Connecting video equipmentSet for use as analog RGB input Projector operation control by a computer How to use the output connector Press ON/STANDBY Remote controlLamp indicator blinks while the lamp is warming up Projection on the screenLanguage Turn on the connected equipment and put it in playback modePress Enter to confirm Control panel Main unit sideInput source selection menu appears Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Press EnterFocus on the picture by turning Adjust the picture size by turningFocusing ring Zooming leverPress the button to decrease volume Press VOL/ADJ +/- to adjust volumePress the + button to increase volume Press ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Press Auto SET Adjusting the picture automaticallyInput full screen video signals from the input Source computer and project the imagePress Keystone Adjust the distortion with the selection buttonsTo finish the adjustment, press Exit repeatedly Correcting the keystone distortionSound and picture are cut off temporarily Icon appears in the mute modeCutting off the picture and sound temporarily Press MutePicture freezes Icon appears in the freeze modeFreezing the picture Press FreezeTo reduce the enlargement ratio, press the Resize button Icon appears in the resize modeEnlarging the picture size Press ResizeSub-picture is displayed Displaying PIP Sub-picturesPress PIP Press Call Displaying InformationStart a presentation on the computer Operating the presentation modeChange a slide with the selection buttons Adjust the projector before presentation if necessarySelect the computer input with Input Press P.MODE and hold for two secondsPress Menu Operating the menu screenStart Adjust with VOL/ADJ +/- or selection buttonsAdjust the image flicker Guide Menu adjustments and settingsReset Full Menu adjustments and settings PictureFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Menu background is normal Reset Full Menu adjustments and settings DisplayFull Menu settings Default setting Full Menu settings Reset PIP menu setting ImagingDocument camera Part names of the document imaging camera modelPreparation of the document imaging camera Light turns on Press ARM LightSet a document to be projected Camera control panelPicture projection with the document imaging camera Press Camera to select the camera input modePut back the arm When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Camera subject which is too dark or vividScreen Locking the white balanceProject a white paper and enlarge it to fill Paper or cloth Correcting illuminated defectsWith the document camera operating, fully Cover the camera lens with a piece of blackMain unit side IndicatorsTrouble indications Control panelDetach the air filter Air filter cleaningUnplug the power cord Take off the front cover Clean the air filterLens side to fix it Mount the air filter and the filter frameMount the front cover Replacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitPull out the lamp Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Take off the lamp cover on the bottom panelSlide the cover into place and tighten the two screws Reset the lamp timerLoad a new lamp Attach the lamp coverSymptom Cause Correction Before calling service personalBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable computer signal Applicable signalCompatible Video and S-Video signal Applicable signalSignal assignment of RS-232C Interface format Controlling the projector by using RS-232CControlling the projector by using RS-232C VLU Computer Resize Main unit SpecificationsReplacement lamp Specifications