Toshiba TLP261, TLP260, TLP560 Air filter cleaning, Unplug the power cord Take off the front cover

Page 62

Air filter cleaning

CONTENTS

62

CAUTION

If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning.

The filter inside the air filter cover is the part to shut out dusts or dregs.

Do not use the projector with the filter taken off.

We recommend you clean the air filter frequently. (The cleaning period is once per 50 hours approximately).

1 Unplug the power cord.
2	Take off the front cover.
	Take off the front cover.
1	Slide the front cover rightward side for
1	about 3 mm, then the front cover can be
	taken off toward you.

2

Front cover

3	Detach the air filter.
	Take off the filter frame by pulling the

middle part of it toward you, then detach the air filter.

Air filter

Filter frame

4	Clean the air filter.
	Clean the air filter.
	Use a vacuum cleaner to carefully remove any dust and dirt from the front
	cover, air filter and filter frame.
	Be careful that the air filter is not sucked into the vacuum cleaner.

Maintenance

Continued

Image 62

Contents TLP260 TLP560/TLP260Safety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Exemption ClausesVentilation Power SourcesSource of Light Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedSafety Check Damage Requiring ServiceReplacement Parts ServicingDo not move the projector while the arm is still erect Do not carry by the camera armHeat could erase or discolor the letters on a thermal paper Do not look into the arm light while it is litPower supply cord selection BeforeContents Anti-theft lock hole Names of each part on the main unitSpeakerLens Carrying handle Names of each part on the main unit ON/STANDBY buttonVideo in connector USB connectorControl connector 26 72 RS-232C connector Computer OUT connectorNames of each part on the remote control Freeze buttonOpen the cover Install the batteriesLoading batteries Attach the coverRemote control operation Front side Rear sideFloor-mounted projector placement Determine the screen size projected on the screen Side viewInsert the other end into a wall outlet Connect the power cordTake off the lens cover Lens shift function Turn the foot adjuster to make fine adjustment to the height Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Connecting a computer Connecting video equipment Audio in jackSet for use as analog RGB input Projector operation control by a computer How to use the output connector Projection on the screen Remote controlLamp indicator blinks while the lamp is warming up Press ON/STANDBYControl panel Main unit side Turn on the connected equipment and put it in playback modePress Enter to confirm LanguagePress Enter Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Input source selection menu appearsZooming lever Adjust the picture size by turningFocusing ring Focus on the picture by turningPress the button to decrease volume Press VOL/ADJ +/- to adjust volumePress the + button to increase volume Press ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Source computer and project the image Adjusting the picture automaticallyInput full screen video signals from the input Press Auto SETCorrecting the keystone distortion Adjust the distortion with the selection buttonsTo finish the adjustment, press Exit repeatedly Press KeystonePress Mute Icon appears in the mute modeCutting off the picture and sound temporarily Sound and picture are cut off temporarilyPress Freeze Icon appears in the freeze modeFreezing the picture Picture freezesPress Resize Icon appears in the resize modeEnlarging the picture size To reduce the enlargement ratio, press the Resize buttonSub-picture is displayed Displaying PIP Sub-picturesPress PIP Displaying Information Press CallOperating the presentation mode Start a presentation on the computerPress P.MODE and hold for two seconds Adjust the projector before presentation if necessarySelect the computer input with Input Change a slide with the selection buttonsOperating the menu screen Press MenuAdjust with VOL/ADJ +/- or selection buttons StartGuide Menu adjustments and settings Adjust the image flickerFull Menu adjustments and settings Picture ResetFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Menu background is normal ResetFull Menu settings Default setting Full Menu settings Reset PIP menu setting Part names of the document imaging camera model ImagingDocument cameraPreparation of the document imaging camera Camera control panel Press ARM LightSet a document to be projected Light turns onPress Camera to select the camera input mode Picture projection with the document imaging cameraCamera subject which is too dark or vivid When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Put back the armScreen Locking the white balanceProject a white paper and enlarge it to fill Cover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothControl panel IndicatorsTrouble indications Main unit sideClean the air filter Air filter cleaningUnplug the power cord Take off the front cover Detach the air filterLens side to fix it Mount the air filter and the filter frameMount the front cover Cleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterTake off the lamp cover on the bottom panel Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Pull out the lampAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable signal Applicable computer signalApplicable signal Compatible Video and S-Video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C VLU Computer Resize Specifications Main unitSpecifications Replacement lamp