Toshiba TLP260, TLP560, TLP261, TLP561 owner manual Remote control operation, Front side Rear side

Page 16

Remote control operation

Point the remote control at the infrared remote sensor and press a button.

CONTENTS

16

Before use

Front side

Rear side

			°
	About		15
	About	5m	About
			About
			°
			°
			15
			About
			°
			15
			About
			°
			15
			About

About

5m

15° About

15° About 15° About

15° About

Notes

•The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the projector’s remote sensor.

•Operate the remote control from a position where the remote sensor is visible.

•Do not drop the remote control or otherwise jolt it.

•Keep the remote control out of locations with excessively high temperature or humidity.

•Do not get water on the remote control or place wet objects on it.

•Do not disassemble the remote control.

•Under unusual circumstances the remote control may not operate well due to the location being used or the surroundings. At such times, change the direction of the remote control to the projector and retry the operation.

Image 16

Contents TLP260 TLP560/TLP260Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Exemption ClausesSource of Light Power SourcesVentilation Important Safety Instructions Accessories Object and Liquid EntryDo not place the product vertically Stack InhibitedDamage Requiring Service Replacement PartsSafety Check ServicingDo not carry by the camera arm Heat could erase or discolor the letters on a thermal paperDo not move the projector while the arm is still erect Do not look into the arm light while it is litPower supply cord selection BeforeContents SpeakerLens Carrying handle Names of each part on the main unitAnti-theft lock hole Names of each part on the main unit ON/STANDBY buttonUSB connector Control connector 26 72 RS-232C connectorVideo in connector Computer OUT connectorNames of each part on the remote control Freeze buttonInstall the batteries Loading batteriesOpen the cover Attach the coverRemote control operation Front side Rear sideFloor-mounted projector placement Determine the screen size projected on the screen Side viewTake off the lens cover Connect the power cordInsert the other end into a wall outlet Lens shift function Turn the foot adjuster to make fine adjustment to the height Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Connecting a computer Connecting video equipment Audio in jackSet for use as analog RGB input Projector operation control by a computer How to use the output connector Remote control Lamp indicator blinks while the lamp is warming upProjection on the screen Press ON/STANDBYTurn on the connected equipment and put it in playback mode Press Enter to confirmControl panel Main unit side LanguageSelect the input source by pressing Input repeatedly Press Input and hold for two secondsPress Enter Input source selection menu appearsAdjust the picture size by turning Focusing ringZooming lever Focus on the picture by turningPress the + button to increase volume Press VOL/ADJ +/- to adjust volumePress the button to decrease volume Press ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Adjusting the picture automatically Input full screen video signals from the inputSource computer and project the image Press Auto SETAdjust the distortion with the selection buttons To finish the adjustment, press Exit repeatedlyCorrecting the keystone distortion Press KeystoneIcon appears in the mute mode Cutting off the picture and sound temporarilyPress Mute Sound and picture are cut off temporarilyIcon appears in the freeze mode Freezing the picturePress Freeze Picture freezesIcon appears in the resize mode Enlarging the picture sizePress Resize To reduce the enlargement ratio, press the Resize buttonPress PIP Displaying PIP Sub-picturesSub-picture is displayed Displaying Information Press CallOperating the presentation mode Start a presentation on the computerAdjust the projector before presentation if necessary Select the computer input with InputPress P.MODE and hold for two seconds Change a slide with the selection buttonsOperating the menu screen Press MenuAdjust with VOL/ADJ +/- or selection buttons StartGuide Menu adjustments and settings Adjust the image flickerFull Menu adjustments and settings Picture ResetFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Menu background is normal ResetFull Menu settings Default setting Full Menu settings Reset PIP menu setting Part names of the document imaging camera model ImagingDocument cameraPreparation of the document imaging camera Press ARM Light Set a document to be projectedCamera control panel Light turns onPress Camera to select the camera input mode Picture projection with the document imaging cameraWhen finished, turn off the light and close it Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Put back the armProject a white paper and enlarge it to fill Locking the white balanceScreen Correcting illuminated defects With the document camera operating, fullyCover the camera lens with a piece of black Paper or clothIndicators Trouble indicationsControl panel Main unit sideAir filter cleaning Unplug the power cord Take off the front coverClean the air filter Detach the air filterMount the front cover Mount the air filter and the filter frameLens side to fix it Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filterLamp replacement Unplug the power cord Wait until the lamp gets cool enoughTake off the lamp cover on the bottom panel Pull out the lampReset the lamp timer Load a new lampAttach the lamp cover Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable signal Applicable computer signalApplicable signal Compatible Video and S-Video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C VLU Computer Resize Specifications Main unitSpecifications Replacement lamp