Toshiba TDP-MT200 owner manual Basic operations, Turn on the power, Activate the connected device

Page 23

English Français Español Deutsch Italiano Português Svenska

Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning the power on” p.21 .

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)

qUse theorbutton to select the desired language and press the button.

Message for setup confirmation is displayed in a selected language.

Then, the menu for lamp power selection and configuration is displayed. It is automatically set as Standard. To change the setting, follow the step w.

wUsing the or button, select the lamp power and press the button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

Notes

•When the projector is turned on the next time, the Language and Lamp power menus do not appear upon startup. However, if “Reset all” is executed from the Default setting menu p.31 , the Language and Lamp power menus will be displayed the next time when the power is turned on.

•The language can also be set via the Display setting menu p.30 and Lamp power via the Default setting menu p.31 .

•This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment.

Notes

•When [Auto input search] is set to [On] in the default setting menu p.31 , the image of the equipment which is connected and turned on is projected.

•Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction.

Operations

23

Image 23

Contents TDP-MT200 USA only Safety PrecautionsBefore Using Ventilation Important Safety InstructionsPower Sources Source of LightWater and Moisture Power-Cord ProtectionCleaning HeatImportant Safety Instructions Servicing AccessoriesDamage Requiring Service Do not use the product in a closed installation state Replacement PartsSafety Check Save Original Packing Materials Power Supply Cord SelectionImportant Precautions Place and Manner of InstallationExemption Clauses Important Precautions Avoid Volatile LiquidOther Cautions and Informations Remote Control BatteriesContents Others Checking the package contents 108 11 Names of each part on the main unitNames of each part on the control panel and remote control Parts on the rear panel Remove the battery cover Insert the dry-cell batteries Preparing and using the remote controlLoading dry-cell batteries into the remote control Operating the remote controlScreen As seen from above PlacementPlacement Styles Projection Distance and SizeBefore connection ConnectionRemoving the lens cover Connecting the power cordTurning the power on Press the ON/STANDBY button again Turning the power on and offTurning the power off Press the ON/STANDBY buttonPress the Input button Turn on the powerBasic operations Activate the connected deviceBasic operations Projector placement angle adjustmentsAdjusting the screen size and focus To adjust the horizontal angle, use the tilt adjusterCorrecting the keystone distortion Using handy featuresUsing auto setting Manual adjustments and settings Using handy featuresFreezing the image Freeze Press the remote control’s Mute buttonPress the remote control’s Freeze button Cutting off the picture temporarily MuteHow to use the menus Using the menusImage adjustment menu Screen size Using the menuDisplay setting menu Auto Default setting menuNo signal Sets the lamp power Low StandardVersion Firmware version Note Displaying Information Status displayAbout lamp Lamp replacementWhen the lamp is broken Lamp replacement Replacing cooling fans Lens and main unit cleaningLens cleaning Main unit cleaningLamp went out during use, or won’t come on No powerPower went out during use Trouble indicationsBefore calling service personnel Separately sold product SpecificationsList of general specifications SpecificationSVGA85 List of supported signals RGB signalsList of supported signals DVI signals SpecificationsPin assignment of Computer terminal List of supported signals Y/PB/PR signalsList of supported signals Video, S-Video signals Pin arrangement for the DVI-D terminal D V I D Interface format Main CommandsControl terminal Pin assignment