Toshiba TDP-MT200 owner manual Control terminal, Pin assignment, Interface format, Main Commands

Page 43

English Français Español Deutsch Italiano Português Svenska

■CONTROL terminal

●Pin assignment

			Pin No.	Signal Name	Description
	7		1	RXD	Receiving data
8	6		2	CTS	Consent to send
			3	DSR	Data set ready
5		3	4	GND	Signal ground
5		3	5	RTS	Request to send
			5	RTS	Request to send
	4		6	N.C	No connection
2	1		7	TXD	Sending data
			8	GND	Signal ground

Mini DIN 8 pin connector

●Interface format

1

Communication method

RS-232C, 9600bps, No Parity, Data Length: 8 bits;

Stop Bit Length:

1 bit

2

Communication format

STX (02h)

Command (3Byte)

ETX (03h)

Only 1 command valid per communication.

3

Data format

For input commands, only ASCII-compliant all-uppercase

alphanumeric characters supported.

4

Replies

Acknowledge

ACK (06h)

CR (0Dh)

Data

... Normally ended

ACK (06h)

ESC (1Bh)

... Aborted

No acknowledge

NAK (15h)

If commands are to be sent consecutively, wait for the response from the projector before sending the next command.

●Main Commands

Item	Command
Power on	PON
Power off	PSD
Icon display on	MO0
Icon display off	MO1
Auto setting (RGB input)	PAT
Status display on	DON
Status display off	DOF

Item	Command
Computer input select	IN1
DVI input select	IN2
Video input select	IN3
S-video input select	IN4
YPB/CBPR/CR input select	IN5

Note

• Contact your dealer for control cable and other commands.

Others

43

Image 43

Contents TDP-MT200 USA only Safety PrecautionsBefore Using Ventilation Important Safety InstructionsPower Sources Source of LightWater and Moisture Power-Cord ProtectionCleaning HeatImportant Safety Instructions Damage Requiring Service AccessoriesServicing Safety Check Replacement PartsDo not use the product in a closed installation state Save Original Packing Materials Power Supply Cord SelectionImportant Precautions Place and Manner of InstallationExemption Clauses Important Precautions Avoid Volatile LiquidOther Cautions and Informations Remote Control BatteriesContents Others Checking the package contents 108 11 Names of each part on the main unitNames of each part on the control panel and remote control Parts on the rear panel Remove the battery cover Insert the dry-cell batteries Preparing and using the remote controlLoading dry-cell batteries into the remote control Operating the remote controlScreen As seen from above PlacementPlacement Styles Projection Distance and SizeBefore connection ConnectionTurning the power on Connecting the power cordRemoving the lens cover Press the ON/STANDBY button again Turning the power on and offTurning the power off Press the ON/STANDBY buttonPress the Input button Turn on the powerBasic operations Activate the connected deviceBasic operations Projector placement angle adjustmentsAdjusting the screen size and focus To adjust the horizontal angle, use the tilt adjusterUsing auto setting Using handy featuresCorrecting the keystone distortion Manual adjustments and settings Using handy featuresFreezing the image Freeze Press the remote control’s Mute buttonPress the remote control’s Freeze button Cutting off the picture temporarily MuteHow to use the menus Using the menusImage adjustment menu Display setting menu Using the menuScreen size Auto Default setting menuNo signal Sets the lamp power Low StandardVersion Firmware version Note Displaying Information Status displayWhen the lamp is broken Lamp replacementAbout lamp Lamp replacement Replacing cooling fans Lens and main unit cleaningLens cleaning Main unit cleaningLamp went out during use, or won’t come on No powerPower went out during use Trouble indicationsBefore calling service personnel Separately sold product SpecificationsList of general specifications SpecificationSVGA85 List of supported signals RGB signalsList of supported signals DVI signals SpecificationsList of supported signals Video, S-Video signals List of supported signals Y/PB/PR signalsPin assignment of Computer terminal Pin arrangement for the DVI-D terminal D V I D Interface format Main CommandsControl terminal Pin assignment