Toshiba TDP-MT200 Trouble indications, No power, Lamp went out during use, or won’t come on

Page 36

Trouble indications

The indicator lights inform you of internal abnormalities.

No power

⇒ Problem with projector

• Unplug the power cord, and contact your dealer. ⇒ The lamp cover is not properly attached.

• Unplug the power cord, and reattach the lamp cover. p.34

(Off)

		Lamp went out during use, or won’t come on
		⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
	(Red lit)	the lamp has ended or the projector is malfunctioning.
	(Red lit)	•	Unplug the power cord and wait for a short while, then turn the power back on.
		•
		•	If a lamp burns out, replace it with a new one.
		❈ After approx. one minute of abnormal display, the projector returns to
		(Red lit)	the standby state waiting for internal cool down.
			the standby state waiting for internal cool down.

		Power went out during use
	(Red lit or flashing)	⇒ Internal overheating, or the outside temperature is too high.
	(Green lit)	• Place the projector so that the air intake and exhaust are not blocked.
	Or (Orange lit)	• Unplug the power cord and wait for a short while, then turn the power back on.
		❈ The	icon will appear before the power goes out.
	(Red lit)	❈ After approx. one minute of abnormal display, the projector returns to
		the standby state waiting for internal cool down.

	Power went out during use
	⇒ Problem with internal cooling fan.
(Red lit or flashing)	• Unplug the power cord, and contact your dealer.
Or (Orange lit)	❈ The	icon will appear before the power goes out.
	❈ After approx. one minute of abnormal display, the projector returns to
(Red lit)	the standby state waiting for internal cool down.

		Power went out during use
(Green lit		⇒ Problem inside the projector.
(Green lit		• Unplug the power cord and wait for a short while, then turn the power back on.
(Green lit or Off)	(Green
or Off)	flashing)	• If the above action will not clear the problem, unplug the power cord,
		and contact your dealer.
(Red lit)		❈ After approx. one minute of abnormal display, the projector returns to
(Red lit)		the standby state waiting for internal cool down.

PRECAUTION

• Make sure to unplug the power cord if something goes wrong.

36

Image 36

Contents TDP-MT200 Safety Precautions USA onlyBefore Using Important Safety Instructions Power SourcesSource of Light VentilationPower-Cord Protection CleaningHeat Water and MoistureImportant Safety Instructions Accessories Damage Requiring ServiceServicing Replacement Parts Safety CheckDo not use the product in a closed installation state Power Supply Cord Selection Important PrecautionsPlace and Manner of Installation Save Original Packing MaterialsImportant Precautions Avoid Volatile Liquid Exemption ClausesRemote Control Batteries Other Cautions and InformationsContents Others Checking the package contents Names of each part on the main unit 108 11Names of each part on the control panel and remote control Parts on the rear panel Preparing and using the remote control Loading dry-cell batteries into the remote controlOperating the remote control Remove the battery cover Insert the dry-cell batteriesPlacement Placement StylesProjection Distance and Size Screen As seen from aboveConnection Before connectionConnecting the power cord Turning the power onRemoving the lens cover Turning the power on and off Turning the power offPress the ON/STANDBY button Press the ON/STANDBY button againTurn on the power Basic operationsActivate the connected device Press the Input buttonProjector placement angle adjustments Adjusting the screen size and focusTo adjust the horizontal angle, use the tilt adjuster Basic operationsUsing handy features Using auto settingCorrecting the keystone distortion Using handy features Manual adjustments and settingsPress the remote control’s Mute button Press the remote control’s Freeze buttonCutting off the picture temporarily Mute Freezing the image FreezeUsing the menus How to use the menusImage adjustment menu Using the menu Display setting menuScreen size Default setting menu No signalSets the lamp power Low Standard AutoDisplaying Information Status display Version Firmware version NoteLamp replacement When the lamp is brokenAbout lamp Lamp replacement Lens and main unit cleaning Lens cleaningMain unit cleaning Replacing cooling fansNo power Power went out during useTrouble indications Lamp went out during use, or won’t come onBefore calling service personnel Specifications List of general specificationsSpecification Separately sold productList of supported signals RGB signals SVGA85Specifications List of supported signals DVI signalsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signalsPin assignment of Computer terminal Pin arrangement for the DVI-D terminal D V I D Main Commands Control terminalPin assignment Interface format