Toshiba TDP-MT200 owner manual Safety Precautions, USA only

Page 2

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

WARNING: USA only

WARNING: USA only

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

This [product] contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.

MODEL NAME: TDP-MT200

USA only

 

 

 

 

 

 

TRADE NAME: DLP™ PROJECTOR

MODEL NAME: TDP-MT200

 

Tested To Comply

 

 

 

With FCC Standards

 

 

 

FOR HOME OR OFFICE USE

 

 

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents TDP-MT200 Safety Precautions USA onlyBefore Using Source of Light Important Safety InstructionsPower Sources VentilationHeat Power-Cord ProtectionCleaning Water and MoistureImportant Safety Instructions Servicing AccessoriesDamage Requiring Service Do not use the product in a closed installation state Replacement PartsSafety Check Place and Manner of Installation Power Supply Cord SelectionImportant Precautions Save Original Packing MaterialsImportant Precautions Avoid Volatile Liquid Exemption ClausesRemote Control Batteries Other Cautions and InformationsContents Others Checking the package contents Names of each part on the main unit 108 11Names of each part on the control panel and remote control Parts on the rear panel Operating the remote control Preparing and using the remote controlLoading dry-cell batteries into the remote control Remove the battery cover Insert the dry-cell batteriesProjection Distance and Size PlacementPlacement Styles Screen As seen from aboveConnection Before connectionRemoving the lens cover Connecting the power cordTurning the power on Press the ON/STANDBY button Turning the power on and offTurning the power off Press the ON/STANDBY button againActivate the connected device Turn on the powerBasic operations Press the Input buttonTo adjust the horizontal angle, use the tilt adjuster Projector placement angle adjustmentsAdjusting the screen size and focus Basic operationsCorrecting the keystone distortion Using handy featuresUsing auto setting Using handy features Manual adjustments and settingsCutting off the picture temporarily Mute Press the remote control’s Mute buttonPress the remote control’s Freeze button Freezing the image FreezeUsing the menus How to use the menusImage adjustment menu Screen size Using the menuDisplay setting menu Sets the lamp power Low Standard Default setting menuNo signal AutoDisplaying Information Status display Version Firmware version NoteAbout lamp Lamp replacementWhen the lamp is broken Lamp replacement Main unit cleaning Lens and main unit cleaningLens cleaning Replacing cooling fansTrouble indications No powerPower went out during use Lamp went out during use, or won’t come onBefore calling service personnel Specification SpecificationsList of general specifications Separately sold productList of supported signals RGB signals SVGA85Specifications List of supported signals DVI signalsPin assignment of Computer terminal List of supported signals Y/PB/PR signalsList of supported signals Video, S-Video signals Pin arrangement for the DVI-D terminal D V I D Pin assignment Main CommandsControl terminal Interface format
Top Page Image Contents