Toshiba TDP-MT200 List of supported signals Y/PB/PR signals, Pin assignment of Computer terminal

Page 41

English Français Español Deutsch Italiano Português Svenska

■List of supported signals (Y/PB/PR signals)

Signal format	fh(kHz)	fv(Hz)
480i(525i)@60Hz	15.73	59.94

480p(525p)@60Hz	31.47	59.94
576i(625i)@50Hz	15.63	50.00
576p(625p)@50Hz	31.25	50.00
720p(750p)@60Hz	45.00	60.00
720p(750p)@50Hz	37.50	50.00
1080i(1125i)@60Hz	33.75	60.00
1080i(1125i)@50Hz	28.13	50.00

■List of supported signals (Video, S-Video signals)

Video mode	fh(kHz)	fv(Hz)	fsc(MHz)
NTSC	15.73	60	3.58
PAL	15.63	50	4.43
SECAM	15.63	50	4.25 or 4.41
PAL-M	15.73	60	3.58
PAL-N	15.63	50	3.58
PAL-60	15.73	60	4.43
NTSC4.43	15.73	60	4.43

■Pin assignment of COMPUTER terminal

5 1



	10			6

15			11
Mini D sub 15 Pin connector
Input Signal
• RGB input
RGB signals:						0.7V (p-p) 75 Ω
Horizontal sync signal:						TTL level (Pos/neg polarity)
Vertical sync signal:						TTL level (Pos/neg polarity)

Pin No.	Pin description
1	Video signal (R)
2	Video signal (G)
3	Video signal (B)
4	GND
5	GND
6	GND (R)
7	GND (G)
8	GND (B)
9	N.C
10	GND
11	GND
12	N.C
13	Horizontal sync signal
14	Vertical sync signal
15	N.C

Others

41

Image 41

Contents TDP-MT200 USA only Safety PrecautionsBefore Using Power Sources Important Safety InstructionsSource of Light VentilationCleaning Power-Cord ProtectionHeat Water and MoistureImportant Safety Instructions Servicing AccessoriesDamage Requiring Service Do not use the product in a closed installation state Replacement PartsSafety Check Important Precautions Power Supply Cord SelectionPlace and Manner of Installation Save Original Packing MaterialsExemption Clauses Important Precautions Avoid Volatile LiquidOther Cautions and Informations Remote Control BatteriesContents Others Checking the package contents 108 11 Names of each part on the main unitNames of each part on the control panel and remote control Parts on the rear panel Loading dry-cell batteries into the remote control Preparing and using the remote controlOperating the remote control Remove the battery cover Insert the dry-cell batteriesPlacement Styles PlacementProjection Distance and Size Screen As seen from aboveBefore connection ConnectionRemoving the lens cover Connecting the power cordTurning the power on Turning the power off Turning the power on and offPress the ON/STANDBY button Press the ON/STANDBY button againBasic operations Turn on the powerActivate the connected device Press the Input buttonAdjusting the screen size and focus Projector placement angle adjustmentsTo adjust the horizontal angle, use the tilt adjuster Basic operationsCorrecting the keystone distortion Using handy featuresUsing auto setting Manual adjustments and settings Using handy featuresPress the remote control’s Freeze button Press the remote control’s Mute buttonCutting off the picture temporarily Mute Freezing the image FreezeHow to use the menus Using the menusImage adjustment menu Screen size Using the menuDisplay setting menu No signal Default setting menuSets the lamp power Low Standard AutoVersion Firmware version Note Displaying Information Status displayAbout lamp Lamp replacementWhen the lamp is broken Lamp replacement Lens cleaning Lens and main unit cleaningMain unit cleaning Replacing cooling fansPower went out during use No powerTrouble indications Lamp went out during use, or won’t come onBefore calling service personnel List of general specifications SpecificationsSpecification Separately sold productSVGA85 List of supported signals RGB signalsList of supported signals DVI signals SpecificationsPin assignment of Computer terminal List of supported signals Y/PB/PR signalsList of supported signals Video, S-Video signals Pin arrangement for the DVI-D terminal D V I D Control terminal Main CommandsPin assignment Interface format