Panasonic DMP-BD70V operating instructions Displays, TV screen and video, Sound

Page 41

Displays

 

 

 

Page

The tape counter is not

≥The seconds display will display as shown on the right for unrecorded parts

 

 

—

 

changing.

of the tape. It will also display like this when the dirty or damaged tape is

 

 

 

 

used or when this unit is malfunctioning. In such cases, contact your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

TV screen and video

The images from this unit do not appear on the television.

Picture is distorted.

Jittering occurs.

The screen changes automatically.

Video is not output in high definition.

The 4:3 aspect ratio picture expands left and right.

Screen size is wrong.

There is a lot of after-image when playing video.

When playing DVD-Video using progressive output, one part of the picture momentarily appears to be doubled up.

Still pictures (JPEG) do not play back normally.

≥Make sure that the television is connected to either the VIDEO OUT terminal, COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.

≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.

≥An incorrect resolution is selected in “Component Video Resolution”, when the television is connected to COMPONENT VIDEO OUT terminals. While stopped, press and hold [∫] and [1] (PLAY) on the main unit at the same time for more than 5 seconds to cancel this setting. Set the item again.

≥If “24p Output” is set to “On” when the unit is connected to a TV through any terminal other than HDMI, images may not display properly. In this case, set “24p Output” to “Off”.

≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch to other images, and a black screen is displayed.

≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video other than 24p images. In this case, turn “24p Output” to “Off”.

≥An incorrect resolution is selected in “HDMI Resolution”, when the television is connected to HDMI AV OUT terminals. While stopped, press and hold [∫] and [1] (PLAY) on the main unit at the same time for more than 5 seconds to cancel this setting. Set the item again. However, Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the bitstream, select “Restore Default Settings” to restore the factory presets and make proper settings.

≥Picture may not be seen when more than 4 devices are connected with HDMI cables. Reduce the number of connected devices.

≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to the screen saver mode automatically if there is no operation for 10 minutes or more.

≥When CD or MP3 is played, the screen switches to Screen Saver mode if there is no operation for 2 minutes after starting playback. (Playback continues.)

≥High definition video cannot be output through the VIDEO OUT terminals.

≥Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video Resolution” in the Setup menu are set properly.

≥Use the television to change the aspect. Refer to your television’s operating instructions. ≥When using a component video cable, set “Progressive” to “Video”. If the situation

is not restored after that, set “TV Aspect” to “4:3 Pan & Scan”. ≥When using an HDMI cable, change “TV Aspect” type to “16:9”.

≥Turn “3D NR” or “Integrated NR” off if it is on.

≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting:

1Connect this unit to the TV with any cable except the HDMI cable.

2When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and “Component Video Resolution” to “480i” in the Setup menu.

≥The images that were edited on the PC, such as Progressive JPEG, etc., may not play back.

11

—

34

34

34

34

36

—

33

—

—

34

—

31, 34

34

31

34

37

Sound

No sound. Low volume. Distorted sound.

Cannot hear the desired audio type.

Cannot switch audio.

Stereo audio is sounding muffled while playing back the VHS

≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the amplifier/receiver if you have connected one.

≥Press [AUDIO] to select the audio.

≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.

≥Audio may not be heard when more than 4 devices are connected with HDMI cables. Reduce the number of connected devices.

≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to “On” in the Setup menu.

≥There are discs for which audio cannot be changed because of how the disc was created.

≥When connecting an amplifier/receiver using an optical digital audio cable or an HDMI cable, you cannot switch the audio if “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” is set to “Bitstream”. Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “PCM” or connect using AUDIO OUT terminal.

≥Tracking is off.

≥The tape being played back is damaged.

11–13, 33

21, 26

—

—

34

—

12, 13, 33

26

—

Reference

41

RQT9412

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Region management information CanadaThe warranty can be found onIf you have any questions contact Canada1-800-561-5505Following Applies only in the U.S.A FCC NoteUnit and media care MaintenanceMedia handling To dispose or transfer this unitTable of contents Using the remote control Accessory27informationRemote control Audio/Video Batteries AC power supply cord CableUser recorded media Media Disc/Card/USB device/Video cassette informationCommercially sold discs Discs that cannot be played in this unit SD cardsSD Memory Card* from 8 MB to 2 GB Sdhc Memory Card from 4 GB to 32 GBEnjoying High Bit rate Audio of BD-Video BD-V Audio and video informationAbout audio from audio output terminals Audio output setting for the various equipment Necessary settings for audio outputRegarding 24p output BD-V To return to the previous screenAbout terminal ConnectionsVideo Connections TV Highest QualityConnecting to your TV, via Component Video OUT Connecting to your TV, via Hdmi AV OUTConnecting to your TV, via Video OUT Video Connections TVHdmi OUT Connecting to Hdmi AV OUT terminalDigital Audio Connections Audio AC power connectionAnalog Audio Connection Power button Power Í/I Remote control and unit reference guideEasy Setting SettingPress Í Power Reprogramming the remote control for TV controlBroadband network connection Firmware updatesAutomatically check the firmware Manually updating the firmwareTesting of IP Address/DNS Settings Network settingsSetting the IP address Setting the DNS-IPTesting of Proxy Server Settings Setting the connection speedSetting the proxy server Press 3, 4 to select Proxy Address and press OKInserting or removing a disc Inserting or removing mediaInserting or removing an SD card Inserting or removing a USB deviceBasic play Playing video contents Press 3, 4 to select the item Press OK Showing Functions menuPress Functions Insert a disc or SD card Chapter playback DVD-VRPress 3, 4, 2, 1 to select the title and press OK Insert a discPress PIP Enjoying BD-Live or Bonusview in BD-Video BD-VEnjoying BD-Live discs with Internet Insert an SD cardInsert a disc, SD card or USB device Playing still pictures JpegPress 3, 4, 2, 1 to select the album and press OK Press 3, 4, 2, 1 to select the still picture and press OKPress 3, 4, 2, 1 to select Set and press OK Press 3, 4 to select Slideshow Settings and press OKPress SUB Menu Press 3, 4 to select Zoom out Press OK Press Status twiceOther operations of Video cassette Playing a video cassette VHSInsert a disc or USB device Playing music CD MP3Press 3, 4 to select the track Press OK Playing a track in another folder MP3Preparation What is Viera Link Hdavi Control?Linked operations with the TV Viera LinkTM Hdavi ControlTM Press the button for Viera Link on the remote control Easy control only with Viera remote controlSelect the player Press SUB MenuWhat you can change with the on-screen menu Changing settings with the on-screen menu except VHSOn-screen menu operations Video PlayAudio BD-V Avchd DVD-VR DVD-V MPEG2Setup menu operations Changing the unit’s settingsSummary of settings Press 3, 4, 2, 1 to select the option and press OKTo select these options, perform steps 1-4 AudioDisplay TV / Device Connection Network Code and press OK To change the code on the remote controlPress 3, 4 to select the code 1, 2, or 3 OthersMP3 About MP3/JPEG filesStructure of folders that can be played in this unit On the television Please confirm SetupMessages On the unit’s display To reset this unit Troubleshooting guidePower Following do not indicate a problem with this unitSound DisplaysTV screen and video Card USB≥This occurs between playlist chapters or scenes Avchd Other difficulties with playbackSpecifications User memo Product ServiceCentralized Factory Service Center Limited Warranty Only for U.S.A. and Puerto RicoCarry-In or Mail-In Service Limited Warranty Limits And ExclusionsWarranty Service Limited Warranty Only for CanadaIf YOU Ship the Product to a Servicentre Panasonic Canada IncLicenses Reproducción básica Conexiones básicasDTS-HD GlossaryBD-J Viera Cast Off Timer On-screen AC Power Connection Angle AudioQuick Start R Ratings level Re-master Remote control Connections
Top Page Image Contents