| References | |||
|
|
|
|
|
|
|
|
|
|
No color | Video system is not supported by the TV | When playback is completely stopped, press the P/N button or set | 35, 54 |
|
|
| the correct TV System in the Setup Menu. |
|
|
|
|
|
|
|
| Saturation set too low | Check the saturation setting on TV and player. | 58 |
|
|
|
|
|
|
| Loose or damaged component video cables | If using component output, check that the three cables are all | 15 |
|
|
| properly plugged in and not damaged. Make sure the color of the |
|
|
|
| plugs match the jacks on both ends. |
|
|
|
|
|
|
|
| Incorrect video output port | If using composite video output, check that the cable is not | 13 |
|
|
| incorrectly plugged into a component video jack. |
|
|
|
|
|
|
|
Incorrect color | Incorrect color space setting | If using HDMI for video output, check the color space setting on | 53 |
|
|
| the TV and player. |
|
|
|
|
|
|
|
| Incorrect component video cable connection | If using component video output, check the three component | 15 |
|
|
| video cables to make sure the signals match on both ends. |
|
|
|
|
|
|
|
Picture rolling or split | Video system is not supported by the TV | When playback is completely stopped, press the P/N button or set | 35, 54 |
|
picture |
| the correct TV System in the Setup Menu. |
|
|
|
|
|
|
|
“No Disc” or | No disc or incompatible disc loaded in player | Eject disc and check. | 28 |
|
“Unknown Disc” error |
|
|
|
|
Dirty disc recording surface | Eject the disc and clean any dirt or fingerprints. | 4 |
| |
|
| |||
|
|
|
|
|
| Disc not properly loaded | Eject disc and make sure the label side is facing up and the record | 28 |
|
|
| side is facing down. |
|
|
|
|
|
|
|
| Condensation on the Laser | Turn on the player, eject the disc and leave the player on for about | 3 |
|
|
| an hour. |
|
|
|
|
|
|
|
Remote control failure | Remote control is out of range | Use the remote control within the effective range. | 11 |
|
|
|
|
|
|
| Low battery | Replace the batteries. | 11 |
|
|
|
|
|
|
| Incorrect remote control code | Make sure that no disc is playing. Aim the remote at the player; | 12 |
|
|
| press and hold the ENTER button on the remote for 5 seconds to |
|
|
|
| set the remote code. |
|
|
|
|
|
|
|
Temporary function | Scratched or damaged disc is used | Replace the disc. | 28 |
|
failure |
|
|
|
|
Some functions are not available during playback | Stop playback completely, then try again. | 28 |
| |
|
| |||
|
|
|
|
|
| Interference from other devices | Identify interference by turning off other devices, and then | 3 |
|
|
| relocate or replace the offending device. |
|
|
|
|
|
|
|
Some Setup Menu | Some setup options cannot be changed while a disc is | Fully stop playback, eject the disc and try the Setup Menu again. | 22 |
|
items are grayed out | playing. Some setup options may be mutually exclusive with |
|
|
|
| other setup options. |
|
|
|
|
|
|
|
|
75