Universal Electronics OCAP 5 manual Programming Device Control

Page 10

Atlas OCAP M1056.fm Page 10 Wednesday, April 30, 2008 2:52 PM

PROGRAMMING DEVICE CONTROL

The Atlas OCAP 5-Device Remote Control is preprogrammed to operate the cable box (converter) provided by your cable system, an RCA TV, a Toshiba DVD player, an RCA VCR, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.

NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and per- form the instructions on “Setting Up a Combo Unit” on page 11. Also refer to “Device Table” on page 8 to find out which devices can be programmed onto each device key.

If you have another brand of cable converter or a satellite receiver you would like to control, you’ll need to unlock the cable ID Lock before changing the converter code (see “Program- ming Cable ID Lock” on page 17).

1.Turn on a device and, if applicable, insert video media, (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.

2.On the remote control, press a device key once

(i.e., VCR, DVD, AUD, TV, or CBL); it will blink once. Then press and hold SETUP until the selected mode key blinks twice.

3.Use the “ÍManufacturer’s Codes” starting on page 25) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the selected mode key will blink twice.

NOTE: If the selected mode key emits a long blink, the entry is invalid. Repeat steps 2 through 3 and try entering the same code again.

4.Aim the remote control at the device and

press PWR once. The device should turn off. If it does not, repeat steps 2 through 3, trying each code for your brand until you find one that works. If it still does not respond, try searching for the code (see “Searching for Your Code” on page 12).

NOTE:

If the device does not have a PWR key, press

 

the (Play) key.

www.urcsupport.com/atlasocap

10

Image 10
Contents Preprogrammed for Your SET-TOP BOX Table of Contents To Disable Backlighting To Enable BacklightingBacklighting Tips Introduction Features and Functions Key Charts Key FunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Checking the Codes Programming Channel Control LockUnlocking Channel Control Changing Volume LockLocking Channel Control to CBL Blink twice Locking Volume Control To One Mode Global Volume Lock Programming Cable ID LockProgramming Macro Keys Programming a Macro KeyProgramming the Master Power Key Using the Master Power KEYClearing a Macro Key Using the Master Power Key Clearing the Master Power KeyWrite those settings RE-ASSIGNING Device KeysClearing Custom Programming Activating Backlighting OptionalTroubleshooting Problem Device key does not blink when you press a keyFCC Notice Additional InformationSetup Codes for Audio Receivers Setup Codes for Audio AmplifiersÍMANUFACTURER’S Codes JBL KLH1023, 1609, 1254 DLO Setup Codes for Audio AccessoriesSetup Codes for Cable Boxes/Converters SSI1256 Setup Codes for DVD Players Setup Codes for Cable/DVR/PVR CombosBBK Cavs ESAGPX JSINAD SVA Setup Codes for DVD Recorders Setup Codes for DVD CombosGOI HTSSKY Setup Codes for DVR/PVR SystemsSetup Codes for TVs UsdtvAOC CCECXC FlexVision 0710 Fujitsu KMC JCBKEC KTVMTC NTC1498, 1523, 1991 SSS TMK TVSSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision