Universal Electronics OCAP 5 manual Clearing Custom Programming, Activating Backlighting Optional

Page 22

Atlas OCAP M1056.fm Page 22 Wednesday, April 30, 2008 2:52 PM

To re-assign another unused device key, substitute it for the VCR key above and then perform the sequence. For example, to re-assign an unused AUD key as a second DVD key, perform

AUDÆSETUPÆ9Æ9Æ2ÆDVDÆAUD.

When a re-assignment is done, the selected device key (e.g., AUD) will blink twice to confirm your choice. At that time, you will need to program device control (see “Programming Device Control” on page 10).

CLEARING CUSTOM PROGRAMMING

The Atlas OCAP 5-Device Remote Control contains a Custom Programming Reset program. You can use it to remove all custom programming, except your setup codes and reassigned device keys.

IMPORTANT: Executing this program will erase all cus- tom settings for Volume Lock, Learned Keys, Tune-In Keys, and Channel Lock. However, your device programming remains.

1.On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2.Enter 9 8 0. The last-selected device key

blinks twice, pauses, and blinks twice again to confirm that all custom programming is cleared.

ACTIVATING BACKLIGHTING (OPTIONAL)

On some models of your Atlas OCAP 5-Device Remote Control, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key. To enable backlighting on a remote with that feature, perform the following step:

1.Press SETUP twice within one second.

Backlighting is turned on.

To disable backlighting, perform the following step:

1.Press SETUP twice within one second.

Backlighting is turned off.

www.urcsupport.com/atlasocap

22

Image 22
Contents Preprogrammed for Your SET-TOP BOX Table of Contents To Disable Backlighting To Enable BacklightingBacklighting Tips Introduction Features and Functions Key Charts Key FunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Checking the Codes Programming Channel Control LockUnlocking Channel Control Changing Volume LockLocking Channel Control to CBL Blink twice Locking Volume Control To One Mode Global Volume Lock Programming Cable ID LockProgramming Macro Keys Programming a Macro KeyProgramming the Master Power Key Using the Master Power KEYClearing a Macro Key Using the Master Power Key Clearing the Master Power KeyWrite those settings RE-ASSIGNING Device KeysClearing Custom Programming Activating Backlighting OptionalTroubleshooting Problem Device key does not blink when you press a keyFCC Notice Additional InformationSetup Codes for Audio Receivers Setup Codes for Audio AmplifiersÍMANUFACTURER’S Codes JBL KLH1023, 1609, 1254 DLO Setup Codes for Audio AccessoriesSetup Codes for Cable Boxes/Converters SSI1256 Setup Codes for DVD Players Setup Codes for Cable/DVR/PVR CombosBBK Cavs ESAGPX JSINAD SVA Setup Codes for DVD Recorders Setup Codes for DVD CombosGOI HTSSKY Setup Codes for DVR/PVR SystemsSetup Codes for TVs UsdtvAOC CCECXC FlexVision 0710 Fujitsu KMC JCBKEC KTVMTC NTC1498, 1523, 1991 SSS TMK TVSSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision