Universal Electronics OCAP 5 manual Checking the Codes, Programming Channel Control Lock

Page 14

Atlas OCAP M1056.fm Page 14 Wednesday, April 30, 2008 2:52 PM

CHECKING THE CODES

If you have set up the Atlas OCAP 5-Device Remote Control by searching for your device code (on the previous page), you may need to find out which four- digit code is operating your equipment.

For example, to find out which code is operating your TV:

1.On the remote control, press TV once; it will

blink once. Then press and hold SETUP until the TV key blinks twice.

2.Enter 9 9 0. The TV key will blink twice.

3.To view the code for the first digit, press 1

once. Count the number of times the TV key blinks (e.g., 3 blinks = 3) and write down the number in the leftmost TV Code box on page 11.

NOTE: If a code digit is 0, the selected mode key will not blink.

4.Repeat step 3 three more times for the

remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Finish writing down the code in the TV Code boxes on page 11.

5.To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (e.g., VCR, DVD, AUD, or CBL) for the device you are checking. Write down the codes in the appropriate boxes on page 11.

PROGRAMMING CHANNEL CONTROL LOCK

By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys* are 1 through 0, CH+, CH-, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can de- activate this feature to allow full access to these keys in the TV and VCR modes.

*NOTE: This feature does not affect the AUD mode.

www.urcsupport.com/atlasocap

14

Image 14
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Backlighting Tips To Enable BacklightingTo Disable Backlighting Introduction Features and Functions Key Charts Key FunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Checking the Codes Programming Channel Control LockLocking Channel Control to CBL Changing Volume LockUnlocking Channel Control Blink twice Locking Volume Control To One Mode Global Volume Lock Programming Cable ID LockProgramming Macro Keys Programming a Macro KeyClearing a Macro Key Using the Master Power KEYProgramming the Master Power Key Using the Master Power Key Clearing the Master Power KeyWrite those settings RE-ASSIGNING Device KeysClearing Custom Programming Activating Backlighting OptionalTroubleshooting Problem Device key does not blink when you press a keyFCC Notice Additional InformationÍMANUFACTURER’S Codes Setup Codes for Audio AmplifiersSetup Codes for Audio Receivers JBL KLH1023, 1609, 1254 DLO Setup Codes for Audio AccessoriesSetup Codes for Cable Boxes/Converters SSI1256 BBK Setup Codes for Cable/DVR/PVR CombosSetup Codes for DVD Players Cavs ESAGPX JSINAD SVA Setup Codes for DVD Recorders Setup Codes for DVD CombosGOI HTSSKY Setup Codes for DVR/PVR SystemsSetup Codes for TVs UsdtvAOC CCECXC FlexVision 0710 Fujitsu KMC JCBKEC KTVMTC NTC1498, 1523, 1991 SSS TMK TVSSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision