Universal Electronics OCAP 5 manual RE-ASSIGNING Device Keys, Write those settings

Page 21

Atlas OCAP M1056.fm Page 21 Wednesday, April 30, 2008 2:52 PM

4.Press and hold SETUP until the CBL key blinks twice.

RE-ASSIGNING DEVICE KEYS

The Atlas OCAP 5-Device Remote Control can be set up to control a second device of an already-assigned type. For example, to have the unit control a TV, a Cable Converter, and two audio devices (for example, two audio receivers), re-assign the unused VCR key to operate the second audio device as follows:

NOTE:

VCR is preset at the factory to control an RCA

 

VCR. Performing the steps below will over-

 

write those settings.

1.On the remote control, press VCR once; it will blink once. Then press and hold SETUP until

the VCR key blinks twice.

2.Enter 9 9 2. The VCR key will blink twice.

3.Press AUD once, then press VCR once. The VCR

key will blink twice.

The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control” on page 10. To re-assign other device keys, repeat these and substitute the key sequence using the following chart:

NOTE: Only one device can be assigned to an unused device key at a time.

To Re-Assign

Perform Key Sequence

 

 

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆAUDÆVCR AUD key

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆTVÆVCR TV key

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆCBLÆVCR CBL key

VCR back to VCRÆSETUPÆ9Æ9Æ2ÆVCRÆVCR VCR

www.urcsupport.com/atlasocap

21

Image 21
Contents Preprogrammed for Your SET-TOP BOX Table of Contents To Enable Backlighting To Disable BacklightingBacklighting Tips Introduction Features and Functions Key Function Key ChartsUse VOL+ or VOL- to raise or lower the audio volume Device Key Device TableInstalling Batteries Programming Device Control On the remote control, press a device key onceSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Programming Channel Control Lock Checking the CodesChanging Volume Lock Unlocking Channel ControlLocking Channel Control to CBL Blink twice Programming Cable ID Lock Locking Volume Control To One Mode Global Volume LockProgramming a Macro Key Programming Macro KeysUsing the Master Power KEY Programming the Master Power KeyClearing a Macro Key Clearing the Master Power Key Using the Master Power KeyRE-ASSIGNING Device Keys Write those settingsActivating Backlighting Optional Clearing Custom ProgrammingProblem Device key does not blink when you press a key TroubleshootingAdditional Information FCC NoticeSetup Codes for Audio Amplifiers Setup Codes for Audio ReceiversÍMANUFACTURER’S Codes KLH JBL1023, 1609, 1254 Setup Codes for Cable Boxes/Converters Setup Codes for Audio AccessoriesDLO SSI1256 Setup Codes for Cable/DVR/PVR Combos Setup Codes for DVD PlayersBBK ESA CavsJSI GPXNAD SVA Setup Codes for DVD Combos Setup Codes for DVD RecordersHTS GOISetup Codes for TVs Setup Codes for DVR/PVR SystemsSKY UsdtvCCE AOCCXC FlexVision 0710 Fujitsu KEC JCBKMC KTVNTC MTC1498, 1523, 1991 SSS TVS TMKSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision