Universal Electronics OCAP 5 manual Searching for Your Code

Page 12

Atlas OCAP M1056.fm Page 12 Wednesday, April 30, 2008 2:52 PM

(for example, TV/VCR). If you perform this procedure correctly, the VCR key will blink twice.

NOTE: If the VCR key did not blink twice after enter- ing the codes last digit, repeat steps 2 through 3 and try entering the same code again.

If you’ve located a setup code that works for your combo device (for example, a TV/VCR Combo) and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (see “Programming Device Control” starting on page 10).

4.Aim the remote control at your combo device

(for example, TV/VCR Combo) and press PWR once. The device should turn off. If it does not respond, repeat steps 2 through 3, trying each code listed for your brand until you find one that works. If it still does not respond, try searching for the code (“Searching for Your Code” starting on page 12).

5.For future reference, write down each working device code in the boxes below:

TV/VCR or TV/DVD Code

TV Code (if used)

SEARCHING FOR YOUR CODE

If your home entertainment device does not respond to the Atlas OCAP 5-Device Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.

For example, to search for a code for your TV:

1.Turn on your TV.

2.On the remote control, press TV once; it will

blink once. Then press and hold SETUP until the TV key blinks twice.

3.Enter 9 9 1. The TV key will blink twice.

www.urcsupport.com/atlasocap

12

Image 12
Contents Preprogrammed for Your SET-TOP BOX Table of Contents To Enable Backlighting To Disable BacklightingBacklighting Tips Introduction Features and Functions Key Charts Key FunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Checking the Codes Programming Channel Control LockChanging Volume Lock Unlocking Channel ControlLocking Channel Control to CBL Blink twice Locking Volume Control To One Mode Global Volume Lock Programming Cable ID LockProgramming Macro Keys Programming a Macro KeyUsing the Master Power KEY Programming the Master Power KeyClearing a Macro Key Using the Master Power Key Clearing the Master Power KeyWrite those settings RE-ASSIGNING Device KeysClearing Custom Programming Activating Backlighting OptionalTroubleshooting Problem Device key does not blink when you press a keyFCC Notice Additional InformationSetup Codes for Audio Amplifiers Setup Codes for Audio ReceiversÍMANUFACTURER’S Codes JBL KLH1023, 1609, 1254 Setup Codes for Audio Accessories Setup Codes for Cable Boxes/ConvertersDLO SSI1256 Setup Codes for Cable/DVR/PVR Combos Setup Codes for DVD PlayersBBK Cavs ESAGPX JSINAD SVA Setup Codes for DVD Recorders Setup Codes for DVD CombosGOI HTSSetup Codes for DVR/PVR Systems Setup Codes for TVsSKY UsdtvAOC CCECXC FlexVision 0710 Fujitsu JCB KECKMC KTVMTC NTC1498, 1523, 1991 SSS TMK TVSSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision