Universal Electronics OCAP 5 manual Blink twice

Page 16
www.urcsupport.com/atlasocap
16
Performing these instructions will set inde- pendent volume control for all programmed devices.

Atlas OCAP M1056.fm Page 16 Wednesday, April 30, 2008 2:52 PM

NOTE: The audio mode’s (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device’s volume in all other modes (i.e., VCR, DVD, TV, and CBL). This can be an advan- tage if, for example, you always listen to home entertainment devices through your receiver’s speakers.

Unlocking Volume Control for a Single Device (Individual Volume Unlock)

1.Assuming Global Volume Lock is active, select

a mode on the remote control that you want to unlock (e.g., CBL) and press it once. Next, press and hold SETUP until the device key blinks twice.

2.Enter 9 9 3. The last-selected device key will blink twice.

3.Press VOL- once. The last-selected device key

will blink four times.

4.Repeat steps 1 through 3 for each device you want volume to be unlocked.

Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, will control only that device’s volume.

Unlocking All Volume Control (Global Volume Unlock) NOTE:

1.

On the remote control, press and hold SETUP

 

until the last-selected device key blinks twice.

2.

Enter 9 9 3. The last-selected device key will

 

blink twice.

3.

Press VOL+ once. The last-selected device key

 

will blink four times.

Image 16
Contents Preprogrammed for Your SET-TOP BOX Table of Contents To Disable Backlighting To Enable BacklightingBacklighting Tips Introduction Features and Functions Key Charts Key FunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Checking the Codes Programming Channel Control LockUnlocking Channel Control Changing Volume LockLocking Channel Control to CBL Blink twice Locking Volume Control To One Mode Global Volume Lock Programming Cable ID LockProgramming Macro Keys Programming a Macro KeyProgramming the Master Power Key Using the Master Power KEYClearing a Macro Key Using the Master Power Key Clearing the Master Power KeyWrite those settings RE-ASSIGNING Device KeysClearing Custom Programming Activating Backlighting OptionalTroubleshooting Problem Device key does not blink when you press a keyFCC Notice Additional InformationSetup Codes for Audio Receivers Setup Codes for Audio AmplifiersÍMANUFACTURER’S Codes JBL KLH1023, 1609, 1254 Setup Codes for Audio Accessories Setup Codes for Cable Boxes/ConvertersDLO SSI1256 Setup Codes for DVD Players Setup Codes for Cable/DVR/PVR CombosBBK Cavs ESAGPX JSINAD SVA Setup Codes for DVD Recorders Setup Codes for DVD CombosGOI HTSSetup Codes for DVR/PVR Systems Setup Codes for TVsSKY UsdtvAOC CCECXC FlexVision 0710 Fujitsu JCB KECKMC KTVMTC NTC1498, 1523, 1991 SSS TMK TVSSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision