Universal Electronics OCAP 5 manual Programming Cable ID Lock

Page 17

Atlas OCAP M1056.fm Page 17 Wednesday, April 30, 2008 2:52 PM

Locking Volume Control To One Mode (Global Volume Lock)

NOTE: The audio mode’s volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will control the audio device’s vol- ume in all other modes (i.e., VCR, DVD, TV, or CBL). This can be an advantage if, for exam- ple, you always listen to home entertainment devices through your receiver’s speakers.

1.On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

2.Enter 9 9 3. The last-selected device key will blink twice.

3.Select a mode (e.g., TV or AUD) which you

want to use to control the volume. The selected device key will blink twice.

Now, when you press VOL+, VOL-,or MUTE, the volume of the selected device (e.g., TV) is controlled regardless of mode.

PROGRAMMING CABLE ID LOCK

The Atlas OCAP 5-Device Remote Control is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable converter or satellite service that you would like to control, then you’ll need to perform the following steps to unlock the ID Lock, enter a new manufacturer’s code, and lock the ID Lock again.

1.Turn on the cable converter.

2.On the remote control, press CBL once; it will blink once. Then press and hold SETUP until

the CBL key blinks twice.

3.Enter 9 8 2. The CBL key will blink four

times, indicating ID Lock is unlocked.

www.urcsupport.com/atlasocap

17

Image 17
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Backlighting Tips To Enable BacklightingTo Disable Backlighting Introduction Features and Functions Key Function Key ChartsUse VOL+ or VOL- to raise or lower the audio volume Device Key Device TableInstalling Batteries Programming Device Control On the remote control, press a device key onceSetting UP a Combo Unit Searching for Your Code Atlas Ocap M1056.fm Page 13 Wednesday, April 30, 2008 252 PM Programming Channel Control Lock Checking the CodesLocking Channel Control to CBL Changing Volume LockUnlocking Channel Control Blink twice Programming Cable ID Lock Locking Volume Control To One Mode Global Volume LockProgramming a Macro Key Programming Macro KeysClearing a Macro Key Using the Master Power KEYProgramming the Master Power Key Clearing the Master Power Key Using the Master Power KeyRE-ASSIGNING Device Keys Write those settingsActivating Backlighting Optional Clearing Custom ProgrammingProblem Device key does not blink when you press a key TroubleshootingAdditional Information FCC NoticeÍMANUFACTURER’S Codes Setup Codes for Audio AmplifiersSetup Codes for Audio Receivers KLH JBL1023, 1609, 1254 Setup Codes for Cable Boxes/Converters Setup Codes for Audio AccessoriesDLO SSI1256 BBK Setup Codes for Cable/DVR/PVR CombosSetup Codes for DVD Players ESA CavsJSI GPXNAD SVA Setup Codes for DVD Combos Setup Codes for DVD RecordersHTS GOISetup Codes for TVs Setup Codes for DVR/PVR SystemsSKY UsdtvCCE AOCCXC FlexVision 0710 Fujitsu KEC JCBKMC KTVNTC MTC1498, 1523, 1991 SSS TVS TMKSetup Codes for TVs DLP 0047 Setup Codes for TV/DVD Combos Hitachi 1960 ILo 1990 Initial Insignia 1963 Jensen 1933 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos ABS Carver 0081 HI-Q Multitech 0000 STS 0240, 0036 Atlas Ocap M1056.fm Page 58 Wednesday, April 30, 2008 252 PM Atlas Ocap M1056.fm Page 59 Wednesday, April 30, 2008 252 PM M1056 Revision