Universal Electronics 4-DEVICE Universal Remote Control manual Troubleshooting, Problem, Solution

Page 30

TROUBLESHOOTING

PROBLEM:

Mode key does not blink when you press a key.

SOLUTION:

Replace the batteries with two (2) new AA

 

alkaline batteries (see page 7).

PROBLEM:

Mode key blinks when you press a key, but home

 

entertainment device does not respond.

SOLUTION:

Make sure you are aiming the remote control at

 

your home entertainment device and that you

 

are within 15 feet of the device you are trying

 

to control.

PROBLEM:

The remote control does not control home

 

entertainment devices or commands are not

 

performing properly.

SOLUTION:

Try all listed codes for the device brand being set

 

up. Make sure all devices can be operated with

 

an infrared remote control.

PROBLEM:

TV/VCR combo does not respond properly.

SOLUTION:

Use the VCR codes for your brand. Some combo

 

units may require both a TV code and a VCR

 

code for full operation (see page 9).

PROBLEM:

No volume on a second TV.

SOLUTION:

Follow instructions in Changing Volume Lock

 

(see page 28).

PROBLEM:

CH+ , CH – , and LAST do not work for your

 

RCA TV.

SOLUTION:

Due to RCA design (1983-1987), only the original

 

remote control will operate these functions.

PROBLEM:

Changing channels does not work properly.

SOLUTION:

If original remote control required pressing

 

ENTER to change channels, press ENTER on the

 

remote control after entering a channel number.

PROBLEM:

Tried “Search Method” and still could not find a

 

working code.

SOLUTION:

Try the “Search Method” again after clearing out

 

the device key as follows: Press and hold SETUP

 

until mode key blinks twice, then release. Next

 

enter 9 - 9 - 2. Then press and release the mode

 

key to be cleared twice.

PROBLEM:

Remote control does not turn on Sony or Sharp

 

TV/VCR Combo.

SOLUTION:

For power on, these products require program-

 

ming TV codes on the remote control. For Sony,

 

use TV code 0000 and VCR code 0032. For Sharp,

 

use TV code 0093 and VCR code 0048.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Atlas Cable 4-DEVICE Table of Contents Introduction Code library for popular video and audio devicesFeatures and Functions Key Charts Use Setup for all programming sequencesUse Guide to display the program guide Press Mute once to turn the sound off or on Use CH+ or CH- to select the next higher or lower channelInstalling Batteries Installing Batteries Programming Device ControlAUD TV/VCR Setup Codes for Audio Amplifiers Setup Codes for Audio ReceiversMANUFACTURER’S Codes ABC Setup Codes for Cable ConvertersSetup Codes for DVD Players GPXSetup Codes for VCRs and PVRs CCEKLH HI-QKEC LXINEC STSTMK Setup Codes for TVs AOCCXC NAD JCBKTV NTCSSS Setup Codes for TV/VCR Combos Press Setup once to lock in the code Searching for Your CodeChecking the Codes Enter 9 8 2. The CBL key will blink four times Programming ID LockTurn on the cable converter Enter 9 8 2. The CBL key will blink twiceProgramming Channel Control Lock Enter 9 7 Press CH- once. The CBL key will blink four timesTo Operate The Master Power Key To Program The Master Power KeyTo Clear The Master Power Key Perform steps 1 and 2 in the above section Press Power onceRE-ASSIGNING Device Keys TV VCRUsing Macros Example Programming a Favorite ChannelTo Clear a Macro Changing Volume Lock To Unlock All Volume Control Global Volume UnlockTo Lock Volume Control To One Mode Global Volume Lock Troubleshooting ProblemSolution Additional Information M4030 04/02
Top Page Image Contents