Klark Teknik DN9340E manual Minimum System Requirements, Microsoft .NET Framework 1.1 available at

Page 6

HELIX DN9340E/DN9344E Remote Control Software

User Guide

2INSTALLING HELIX RCS

2.1Minimum System Requirements

Operating System:	Windows 2000 or Windows XP
Computer/Laptop:	Display resolution minimum 1024 X 768 pixels set at 96 DPI
	Pentium III 500MHz (or equivalent)
	256MB RAM
	Minimum 10MB of free disk space on hard drive
Connectivity:	Connection to the DN9340E/DN9344E units is via Ethernet (also with wireless
	option), with the units operating V4.00 host code (or later). There is also an
	option for serial connection, achieved via the front panel. Full connection
	options and respective equipment requirements are detailed in Sections 7 and
	9 of this document.
Software:	The following software must be installed prior to installing the HELIX Remote
	Control Software:
	Microsoft .NET Framework 1.1 available at:
	http://microsoft.com/downloads/details.aspx?FamilyId=262D25E3-F589-
	4842-8157-034D1E7CF3A3&displaylang=en
	Midas ELGAR Library Manager Shell available at:
	http://www.midasconsoles.com

6 of 65

Image 6

Contents Helix DN9340E/DN9344E Helix DN9340E/DN9344E Remote Control Software Contact DetailsContents STORING/RECALLING Memory Settings Introducing the Helix Remote Control Software Minimum System Requirements Microsoft .NET Framework 1.1 available atMidas Elgar Library Manager Shell available at Software Installation Helix DN9340E/DN9344E Remote Control Software Opening Helix RCS within the Elgar Library Manager To add-in an Helix RCS device to the Elgar Library ManagerTo quickly switch to a different view on the same channel DN9340 Device WorkspaceQuick Tour of the DN9340 Device Views To quickly switch to a different view on the other channel Network Identification Specify the Helix unit details in the upper Home tabLinking and Bypassing Channels Specify channel details in the lower Home tabTo link the channels for identical operation Graphic Equalisation To switch to the Graphic Equalisation viewTo specify the EQ mode for the current channel GraphicTo reset all faders to zero To adjust a fader levelTo adjust a group of faders together To switch a fader out of the circuitParametric Equalisation To switch to the Parametric Equalisation viewTo set the Parametric EQ mode for the channel ParaTo add a PEQ section to the graph To switch a PEQ section out of the circuitTo Bypass the parametric EQ on the current channel To activate the target at an existing PEQ sectionDynamic Equalisation To switch to the Dynamic Equalisation viewTo set the Dynamic EQ mode for the channel DynamicTo Bypass the Dynamic EQ on the current channel To shape a Dynamic EQ sectionTo activate the target on the other Dynamic Filters To switch a Dynamic section out of the circuitTo switch to the Filter view FilterTo Bypass all the Filters on the current channel At the Filter Mode tabTo switch a Filter out of the circuit To add a Filter to the graphTo switch to the FastNav screen Building your Network RemotelyFastNav Screen Helix DN9340E/DN9344E Remote Control Software To copy settings from one device to another Copy Channels ScreenGlobal Graphic Screen HintConnecting the Helix DN9340/DN9344E units in a daisy chain OverviewHelix DN9340E/DN9344E unit interconnections Ethernet Connection Ethernet connection standardEthernet connection wireless option Configuring the Network DevicesTo configure an Ethernet device and assign a port to it Helix DN9340E/DN9344E Remote Control Software Click OK Wireless Routing IP AddressingWireless Network Settings Access PointIP settings Security SettingsWireless Card Wireless network properties windowWireless Network Connections screen Helix DN9340E/DN9344E Remote Control Software If your laptop/PC has a firewall Serial connection details Connection ProcedureSerial Connection Option Laptop/PC Cable/Converter Required Unit ConnectionHelix DN9340E/DN9344E Remote Control Software Helix DN9340E/DN9344E Remote Control Software System Configuration Window Finding ports and device namesTo find all ports on your system Port Configuration screen To find new devices attached to your PCHelix DN9340E/DN9344E Remote Control Software Working Online Communications OverviewVersion Update Online OperationTo check the online status of the Devices in the network To cancel online connection during pollingTo take a unit offline To set the Rapide unit online/offlineTo take the entire network offline Activity IndicatorsTroubleshooting All Units OfflineTo open the System Solo Tracking Setup screen Solo Tracking OperationTo assign solo sources to Helix channels Helix DN9340E/DN9344E Remote Control Software Protecting System Settings To change lockout settingsFunction Locking To change the current password Change PasswordTo switch to the Memory view Memory Working with Individual AddInsHelix DN9340E/DN9344E Remote Control Software To retrieve all the Memories from a Unit to the AddIn Device To write all the Memories from the AddIn Device to the unitGlobal Memory Management To open the global Memory Management screenTo Read/Write All Memories from/to multiple units Switch to the Store \ Recall Memory tab Recall From Memory Store To MemoryTo return to the FastNav screen, click Glossary of Terms and Abbreviations AddInSsid Remote Control Connection Options To connect a single unit USB to front panelTo connect a single non-Ethernet unit USB to rear panel Helix DN9340E/DN9344E Remote Control Software Helix DN9340E/DN9344E Remote Control Software Helix DN9340E/DN9344E Remote Control Software Helix DN9340E/DN9344E Remote Control Software Setting up the Lantronix UDS1100 Converter Web Configuration and Telnet Configuration tabs Apply Settings Connecting the system equipmentTo connect up a Helix RCS Ethernet System LAN

Related manuals

Manual 76 pages 248 b