Fortinet 2 SXRC manual Surface Mounting With Screws

Page 10

Installation

Surface Mounting With Screws

The SXRC Control Head can also be surface mounted if you do not have a spare DIN opening in your dash or do not want to cut one into an existing panel.

The back of the SXRC Control Head has two metal inserts designed to work with M3 screws.

Center to Center

5-17/32" (140mm)

Inserts for M3 Screws

Find a suitable location and drill two 1/8 inch (3 mm) holes to secure the SXRC Control Head.The holes should be 5-17/32” (140 mm) apart from center to center.

NOTE: You will need to have access to the area behind this location to install the mounting screws.

Mounting Surface

Center to Center

5-17/32" (140mm)

Once your holes are drilled you can use the two supplied M3 screws to secure the SXRC Control Head to your mounting surface. If the supplied screws are not long enough to reach the SXRC Control Head you can supply your own M3 screws of the required length to secure the SXRC.

Mounting Surface

NOTE!!! Whether using the supplied M3 screws from the SXRC kit or your own, the screws can not enter into the SXRC more than 5/16” (4 mm). If you attempt to insert the screw any deeper than this into the SXRC Control Head you will run the risk of damaging the unit.

NO MORE THAN 5/16" (4 mm)

Mounting Surface

Route the SXRC Control Head cable to your SXRC Interface Box location.Your SXRC Control Head is now mounted and you can move on to the wiring section of this manual.

Mounting Surface

10	SXRC Remote Control

Image 10

Contents Page Sxrc SxrcSxrc Remote Control Sxrc Remote Control Kicker Rubber Mounting Washers Includes four VFD DisplayENT Used to enter the selected menu KeypadESC Used to exit the current menu Home Used to return to the Main Menu and otherBe sure you will have a minimum Standard DIN sized openingOther surface panel to mount the Sxrc Sxrc Control Head Mounting Clips Screws HereSurface Mounting With Screws Kicker Kicker 87654321 Run the supplied Blue Green Blue-White Green-WhiteOrange-White Brown-White Please read Reconnect cablesBetween each step Instructions and followMenu of the amplifier Default MenuPress the ENT key to enter the Main Press the UP or Down key untilVerriiffy ok Avve ye sAvve no SttoorreedAmplifier to control then continue with Step Did you check the pins #1 and #8 in the SX SeriesPlace If you have made your own cables double check them forUP or Down key to scroll through the options Press the ENT key to select InstallationIf you select Save YES then you choose which Global You want to use is selected press the ENT key toInserted properly and ‘snapped’ into place Go back and double check your Communications NetworkAre Straight-Through Ethernet Network cables ENT key to select Installation By using the UP or Down key to scroll throughGo back and double check your Communication Network Amplifiers to make sure they are not bent or damaged?Amplifiers to make sure they are not bent or damaged? Connected ...we can see Oklahoma Operation Navigation You! Plus...it is quicker than a Google search This name to whatever you like. See the Sxrc Setup sectionSxrc Setup section of the manual ManualDrvc level .5 dB and each press Down key to change the Drvc levelDisplay will instantly show the current Down key decreases the Drvc level .5 dBMain Amp addjAMP ADJ Otth chhnns 1005 10Requenc y Through frequency, boost/cutPress the ENT key to select Menu and choose another function to adjust OperationLope HI-PASS menu and lower the high pass crossover pointMenu and choose another function to adjust LO-PASS menu and raise the low pass crossover pointBoth chns, left chn and right chn Oth chhnnsDegree or180 degree. Press the ESC Use the UP or Down keys to select fromThrough both chns, left chn and right Mute on or mute off. Press the ESCRed-liinne Menu the Komp indicator on the IsisAdjustments in the Kompressor While you are in the KompressorBypass OFF or Bypass on Function to adjustBypasss offf 8V Range or 16v rangeThrough Remote on and Remote OFF Remotte onThrough noise off and noise on Pink noise generatorGroup ADJ Can be created in the Sxrc Setup menuWill either be the default name from Any name you may have assigned toExample When you try to increase or decreaseGain setting of this group, nothing will AmpDisplay, the highest gain setting of the group Adjustments in the Gain menuKicker uses a default Q Boost/cut , bandwidth options menu. YouWhile in the frequency and slope options Indicates you are making adjustments in the HI-PASS menu Chns,left chn and right chn options Key to save your setting and return to the bothMenu and choose another function to adjust Both chns,left chn and right chnBoth chns ,left chn and right chn Chns, left chn and right chn optionsIf you select the Kompressor Turn it OFF for this group1v raanngge Another group function to adjustEd-li n e Through from 24.0 db to-24.0 dBYou view each amplifier’s built in trouble Shooting and diagnostic toolsSick BAY Available tools in the Sick Bay menu areReal time Viewing when you have multiple ampsSelected amplifier’s current +12 volt Lock Same make or nameSelected amplifier’s minimum +12 Sx-50000//2Voolltts Volt terminal reading will be displayedSx -50000//2 Selected amplifier’s total run time No hiissttoor y=llo-voollt Reading will be displayedLl ammpps 45 hrThrough Select AMP or ALL Amps Select Noise on or Noise OFF for You can then use the UP or Down keys to»autosearch All»display »group amps»scrnsaver »led »brightness »set time »temp. c/f»hold time »set date »led TimeOff and auto Protected by the backup battery Intensity modes, On and Dim. When Level set in this menu. The default settingDefault setting from Kicker is Keys are not being used they will dim toReturn to the Sxrc Setup menu Autosearch function»groups »group name »assign »release »link »remote volRoouup Amplifiers you are wanting to use More amplifiers available to assignGroup Select itNo amplifiers currently assigned to that Amplifier will be displayedLink Off Group ADJ »EQLink Off AMP ADJ Link On AMP ADJExample Big baasss When done selecting the current group’sSet to Remote OFF Sxxrrc Which character you want to changeSx-50000//2 Emmoorry Bass, center, front, rear, etcOaaddiinng Avve alllAiit EaarrcchThrough the four memory locations By using the UP or Down key to scrollWhen the memory you want to use is selected Press the ENT key to storeAiilleed Erriiffy =0Kiicckkeer LoocckkeedSecurity Press the ENT key to enter your lock code AgainStoring a Preset Recalling a Preset» EQ Sxrc Remote Control Operating Voltage Internal Fusing in Sxrc Interface BoxPower, Ground, Remote Remote Turn-On VoltageFrom the SX Interface Box Disconnect the power harnessTo replace the fuse, first Fuse Good Fuse Blown€ Blue LED on, no display on Sxrc Control Head € Blue LED off€ Blue LED on, garbage characters in display †Select Remote Vol € Everything powers up and looks great, just no sound€ Other problem, I am lost, I don’t know, Help †Select OffAmplifier Remote Address Name Amplifier HelpWhat is not COVERED? Today’s System Diagram Tomorrow’s System Diagram My Future ‘Drool’ System Cash Money Plan Pizza Delivery Earl’s Thoughts